检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:唐子金[1] 董军[1] 张晓强[1] 叶永春[1] 张社伟[1]
机构地区:[1]中国石化集团江汉石油管理局沙市钢管厂,湖北荆州434001
出 处:《焊管》2009年第2期27-35,共9页Welded Pipe and Tube
摘 要:介绍了用于西气东输二线工程的X80钢级、φ1 219 mm×22 mm直缝埋弧焊管和X80钢级、φ1 219 mm×18.4 mm螺旋埋弧焊管的试制情况及检验结果。根据工艺评定结果确定:X80级、φ1 219 mm×22 mm直缝埋弧焊管采用钝边7 mm、坡口角度37°对称X型坡口,预焊焊丝为CHW60Cφ3 mm、内外焊采用MK-680φ4 mm焊丝与神剑SJ101G焊剂匹配以及相应的焊接规范;X80钢级、φ1 219 mm×18.4 mm螺旋埋弧焊管采用钝边7 mm、上坡口角度35°、下坡口角度40°X型坡口,内外焊采用H08C焊丝与锦州SJ101G焊剂匹配以及相应的焊接规范。试制结果均符合API SPEC 5L管线钢管规范和《西气东输二线管道工程用直缝埋弧焊管技术条件》的要求。比较发现X80钢级、φ1219 mm×22 mm直缝埋弧焊管的屈服强度、屈强比相对钢板原料显著上升,伸长率显著下降;X80钢级、φ1 219 mm×18.4 mm螺旋埋弧焊管的屈服强度、屈强比相对卷板原料略有上升,伸长率显著下降,抗拉强度变化不明显。This article introduced trial production and inspection & test results of X80 grade Ф1 219 mm ×22 mm LSAW pipe and 61 219 mm × 18.4 nan SSAW pipe used for The Second West to East Gas Pipeline Project. According to test result of procedure qualification,it was determined to adopt symmetrical X type bevel with 7 mm,bevel angle 37°,pre-welding with CHW60C 63 mm welding wire,inside and outside welding adopt MK -680 Ф4 mm welding wire matched with Shenjian SJ101G welding flux and corresponding welding specification for X80 grade Ф1 219 mm ×22 mm. For X80 grade Ф1 219 mm× 18.4 mm SSAW pipe,it adopt X type bevel with 7 mm and up bevel angle 35°,down bevel angle 40°,and inside and outside welding adopt H08C welding wire matched with Jinzhou SJ101G welding flux and corresponding welding specification. Trial production results meet the requirements of API SPEC 5L Specification and LSAW Pipe Technology Specification of the Second West to East Gas Pipeline Project. It was found that yield stress and Y/T ratio of X80 Ф1 219 mm ×22 mm I-SAW pipe rise obviously comparing to steel plate,elongation decrease remarkably. Yield stress and Y/T ratio of X80 Ф1 219 mm ×22 mm SSAW pipe rise slightly comparing to steel plate,elongation decreasing obviously,tensile stress without remarkable variation.
关 键 词:西气东输二线工程 X80级管线钢管 直缝埋弧焊 螺旋埋弧焊
分 类 号:TG113.2[金属学及工艺—物理冶金]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.31