检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:黄洪亮[1] 许永久[1] 王磊[1] 冯春雷[1] 张勋[1] 张禹[1] 周爱忠[1]
机构地区:[1]中国水产科学研究院东海水产研究所,农业部海洋与河口渔业重点开放实验室,上海200090
出 处:《中国水产科学》2009年第4期596-604,共9页Journal of Fishery Sciences of China
基 金:国家863计划项目资助课题(2006AA10030105);国家自然科学基金项目资助课题(40876049);国家科技支撑计划(2006BAD09A05;2007BAD43B04);上海市重点学科建设项目(T1101)资助
摘 要:采用模型试验,3种不同网片分别为六角形目经编网片RHN、菱形目无结经编网片KRNDM、菱形目有结绞捻网片KTNDM,规格均为1.7mm(水平缩结长度)×1.7mm(垂直缩结高度)。在不同流速下,通过改变网片的水平缩结系数(Et,分别为0.65、0.707、0.60),对网片的阻力性能和运动变化(水平位移和垂直位移)进行研究。结果如下:(1)网片固定时,菱形目网片的阻力在水平缩结范围(Et=0.60~0.707)内,随着缩结增大而逐渐减小。六角形目网片阻力在3者中最大,有结绞捻网片阻力最小,六角形目网片阻力与缩结关系不明显。3种网片之间的阻力差值随流速的增加而增大。(2)缩结系数对于水平位移和垂直位移的影响随网片的结构差异而不同。缩结系数相同时,六角形目网片的水平和垂直位移均为最大,有结绞捻网片均最小。(3)网片的阻力与水平垂直位移受迎流面积的影响。在缩结系数范围内(Et=0.60~0.707)设计网片时首先应考虑网片结构和网线粗度,其次考虑结节,最后考虑缩结系数。The Raschel Hexagonal Net (RHN), the Knotless Raschel Netting in Diamond Mesh (KRNDM)and the Knotted Twisting Netting in Diamond Mesh (KTNDM), with each of horizontal length of hanging and vertical length of hanging being 1.7 m, were studied by the model test in the flume tank. Based on the comparison through change of hanging ratios under different velocity of flow (Et as 0.65,0.707,0.60 respectively), the results of netting resistance characteristics and motion change (horizontal displacement and vertical displacement)were obtained: (1)The resistance of Netting in Diamond Mesh was inversely proportional to the hanging ratio between the range 0.60 and 0.707 during fixation. The netting resistance of RHN was the highest of the three under the test conditions. The RHN was not well correlated with the hanging ratio. The difference value between every two nets increased with the velocity of flow. (2) The variation of Horizontal Displacement (HD) and Vertical Displacement (VD) influenced by hanging ratios differs with kinds of net. The HD and VD was inversely proportional to the hanging ratio between the range 0.60 and 0.707 during fixation. Under the same hanging ratios, the HD and VD of RHN was the highest, the next was for KRNDM, and the lowest was for KTNDM. The netting resistance, HD and VD were correlated with the line area. Within the range of 0.60 to 0.707 during the net designing process, the net structure and line thickness should be paid the most attention, the next is for net node, and the last is for hanging ratio.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.7