木材在线性增长热流下着火的复合判据研究  

On the comprehensive auto-ignition mechanism for wooden material under linearly increasing heat-flux

作　　者：季经纬[1] 郝耀华[1] 王玉娥[1] 张敬瑶[1] 李金鸽[1] 

机构地区：[1]中国矿业大学安全工程学院,江苏徐州221008

出　　处：《安全与环境学报》2009年第6期116-120,共5页Journal of Safety and Environment

基　　金：国家自然科学基金项目(50406026);中国矿业大学科技基金项目(2006B001)

摘　　要：为探索木材在热流变化时的着火特点并提出着火判据,通过试验研究了木材在线性增长热流条件下的自发着火性能,测定了泡桐、椿木、榆木和刺槐4种木材的点燃时间、木材表面的入射热流以及试样内部的温度。结果表明,当热流增长率大于等于0.199kW/(m^2·s)时,试验的所有木材均可以被点燃,点燃这些木材的临界热流增长率介于0.065～0.103 kW/(m^2·s)。建立了木材着火的计算模型,计算得出木材自发着火时的表面温度约为500℃。根据试验和计算的结果提出了结合表面温度和临界热流增长率的木材自发着火复合判据。This paper intends to present our investigation and experimentation results of our study on auto-ignition characteristics of wooden material at a variable heat flux so as to disclose the auto-ignition mechanism. For our research purpose, we have also observed and tested the auto-ignition behaviors of wood under the conditions of a variable linear increase of the heat-flux with the device for fire performance at the early stage （DEPES） . In our study, the output power of the radiation plate in the DFPES were adjusted to 30%, 40%, 50%, 60%, 70%, 80% and 100% so as to form a sequence of variable heat flux with an increasing rate from 0.065 kW/（m^2· s） to 0. 968 kW/（ m^2·s）. When we did our experiments, we were trying to use four kinds of wood, i.e. paulownia, toon, elm and acacia, with the ignition time, the incident heat flux and interior temperature being measured carefully. The heat flux to be introduced to the sample surface was measured by a non-water-cooled heat-flux gauge and the interior temperature was checked by three thermocouples which were inserted in the sample before the test. Test results of ours show that all of the samples can be ignited if the heat flux increasing rate is greater than 0.199 kW/（m^2·s） . But if the heat flux increasing rate is less than 0.199 kW/（m^2· s）, some of the samples used would fail to get ignited. Thus, the experimental facts we have found prove that the critical heat flux increase rate for wood ignition is between 0.065 kW/（m^2· s） and 0. 103 kW/（m^2· s） . Based on the heat conduction model, a numerical model has been developed to calculate the variation of the wood temperatures. Since the wood ignition time can be measured in the tests, the surface ignition temperature can be worked out with the help of the numerical model, with the value of the autoignition temperature being about 500 ℃ for wood. And, finally, a comprehensive autoignition criteria, including the surface temperature and the critical heat flux increasing rate can be

关 键 词：安全工程 着火性能 木材 线性增长热流 复合判据 

分 类 号：TK121[动力工程及工程热物理—工程热物理]