超高强度钢立铣工件温度分析及对加工表面质量的影响  被引量:8

Workpiece temperature analysis and its impact on machined surface quality of ultra-high strength steel in end milling

在线阅读下载全文

作  者:杨升[1] 董琼[1] 彭芳瑜[2] 林森[1] 闫蓉[1] 

机构地区:[1]华中科技大学国家数控系统工程技术研究中心,武汉430074 [2]华中科技大学数字制造装备与技术国家重点实验室,武汉430074

出  处:《航空学报》2015年第5期1722-1732,共11页Acta Aeronautica et Astronautica Sinica

基  金:国家重点基础研究发展计划(2011CB706803);国家自然科学基金(51121002);湖北省重大科技创新计划(2013AAA008)~~

摘  要:以航空难加工材料300M钢为研究对象,基于立铣加工中的工件温度判断在铣削加工中是否出现了金相组织转变,进而分析不同工况下影响加工表面质量的因素。首先,将移动热源法应用于铣削加工中,计算考虑后刀面磨损的立铣加工工件温度,实验表明,计算值与实验值相比误差在10%以内。然后,分析了工件温度在时间上与空间上的分布,以及不同刀具磨损和加工参数条件下工件表面的温升规律,据此预测加工表面是否出现了组织转变,并结合金相组织观察进一步确认。最后,依据加工表面质量物理层面残余应力和显微硬度的检测数据,初步探讨了各因素对表面质量的影响。结果表明,在研究的加工参数范围内,并未达到金相组织转变温度,表面质量主要受铣削热力作用下的剪切面塑性凸出效应、后刀面挤光效应和热效应的影响。300M steel is chosen for the research object, which is the typical difficult-to-cut material in aviation industry. Mi- crostructure changes are judged in milling based on the workpiece temperature. Then the main factors affecting the quality of the machined surface are also analyzed under different cutting conditions. Firstly, moving heat source method is applied to the milling process. The workpiece temperature model of end milling is established considering the flank rubbing effect. The temperature model is confirmed by the temperature measuring experiment and the error is less than 10%. Secondly, Tem- perature model is used to analyze the temperature variation on the workpiece surface over time, as well as the distribution a- long the depth into workpiece. The influences of processing parameters and tool wear on the surface temperature rise are studied. Finally, the quality of machined surface in physical level such as residual stress and microhardness is analyzed with different cutting conditions according to the test data. The results show that within the range of processing parameters stud- ied, workpiece temperature is not higher than the phase transformation temperature. So, surface quality is mainly affected by the plastic bulge, flank squeezing and thermal effect caused by the milling force and temperature.

关 键 词:300M钢 立铣 工件温度 相变 残余应力 显微硬度 

分 类 号:V261.23[航空宇航科学与技术—航空宇航制造工程] TG501.4[金属学及工艺—金属切削加工及机床]

 

参考文献:

正在载入数据...

 

二级参考文献:

正在载入数据...

 

耦合文献:

正在载入数据...

 

引证文献:

正在载入数据...

 

二级引证文献:

正在载入数据...

 

同被引文献:

正在载入数据...

 

相关期刊文献:

正在载入数据...

相关的主题
相关的作者对象
相关的机构对象