氧化镱对碳钢表面化学镀Ni-Zn-P合金的影响  

Effects of Ytterbium Oxide on Electroless Plating Ni-Zn-P Alloy on Surface of Low Carbon Steel

作　　者：万丽娟[1] 蒋柏泉[1,2] 魏林生[2] 

机构地区：[1]南昌大学科技学院生化系,南昌330029 [2]南昌大学环境与化工学院,南昌330031

出　　处：《表面技术》2015年第7期11-15,共5页Surface Technology

基　　金：国家自然科学基金(11105067)~~

摘　　要：目的改善Ni-Zn-P合金镀层的制备工艺和镀层的物理性能。方法鉴于稀土镧系元素因特殊电子结构表现出优异的物理和化学性能,向基础镀液中添加Yb2O3,在低碳钢钢管表面化学镀沉积NiZn-P合金镀层。通过称量法算得沉积速率,通过盐水浸泡实验测试镀层耐蚀性,采用扫描电镜观察镀层的表面形貌,用X-射线衍射仪检测镀层的晶体结构,考察镀液中Yb2O3浓度对镀层的沉积速率、表面形貌、耐蚀时间、晶体结构等的影响。结果随着Yb2O3浓度的增大,镀层的沉积速率呈先升高、后下降的趋势,镀层的表面形貌、耐蚀时间和晶体结构均是先得到改善,而后被削弱。向基础镀液中添加15 mg/L Yb2O3后,镀速提高了21.6%,耐蚀时间延长了16.7%,镀层由粗糙、灰暗、不均匀和有缺陷,变为平整、光亮、均匀和致密,镀层的非晶相程度得到一定强化,耐蚀性能有所提高。结论基础镀液中添加Yb2O3的适宜质量浓度为15 mg/L,该条件下可提高Ni-Zn-P合金的镀速,并改善镀层的质量。Objective To improve the technical process and physical property of Ni-Zn-P alloy. Methods In view of the special electronic structures and excellent physical and ehemieal properties of rare earth lanthanide elements, ytterbium oxide （ Yb2 O3 ） was added into the basic plating solution to deposit Ni-Zn-P alloy coating on the surface of low carbon steel tube. The weight method, the salt water immersion method, scanning electron microscopy （SEM） and X-ray diffracometer （XRD） were used to calculate the deposition rate, measure the corrosion resistance, observe the surface morphology and detect the crystal structure of the coating, respectively. The effects of Yb2O3 concentration on deposition rate, surface morphology, corrosion resistance time and crystal struc-ture of the coating were investigated. Results The experiment showed that with the increase of Yb203 concentration, the deposition rate firstly increased and then decreased, and the surface morphology, corrosion resistance time and crystal structure of the coating were also firstly improved and then weakened. When 15 mg/L Yb2O3 was added into the basic plating solution, the deposition rate was increased by 21.6% , the corrosion resistance duration was extended by 16.7%, the rough, grey dark and uneven surface with defects became smooth, bright, uniform and dense, the amorphous phase levels were reinforced to certain degree and the corrosion resistance ability was improved. Conclusion The suitable mass concentration of Yb2O3 added into the basic plating solution is 15 mg/L, under which the deposition rate can be increased and the coating quality of Ni-Zn-P alloy can be improved.

关 键 词：化学镀 氧化镱 Ni-Zn-P合金 稀土 

分 类 号：TQ153.3[化学工程—电化学工业]