检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
机构地区:[1]中国科学院寒区旱区环境与工程研究所冻土工程国家重点实验室,甘肃兰州730000
出 处:《岩土力学》2016年第5期1373-1379,共7页Rock and Soil Mechanics
基 金:国家重点基础研究发展计划项目(973计划)(No.2012CB026106);优秀国家重点实验室专项基金(No.41023003);冻土工程国家重点实验室自主课题(No.SKLFSE-ZT-07)~~
摘 要:通过对泥浆制样法制备的冻结粉质砂土的单轴压缩试验,系统地研究了冻结砂土在一个宽泛应变率以及含水率范围内的单轴压缩破坏应变特性和线弹模量特性。结果表明:随着应变率的增加,当含水率为12.0%,破坏应变逐渐增大;当含水率在16.7%~24.0%范围内时,破坏应变先增大后减小;当含水率大于等于30.6%时,破坏应变逐渐减小,3种情况下破坏应变最终都逐渐趋于稳定。破坏应变随含水率增加而先急剧增大到一个最大值,然后急剧减小,当含水率超过41.5%时,基本趋于冰的破坏应变。线弹模量先随着应变率的增大而非线性增大到一个最大值,然后应变率的继续增大使线弹模量逐渐减小,线弹模量与应变率的关系满足二次抛物函数规律。在温度为-2.0℃,应变率小于4.67×10-3 s-1的条件下,线弹模量随着含水率的增大而非线性增大,直至最后趋于冰的线弹模量;而在大于等于该应变率的条件下,随着含水率的增大,线弹模量先增大到一个最大值,然后减小趋于冰的线弹模量。当温度为-5.0℃时,类似的应变率临界值为1.00×10-2 s-1。Based on a mud method of preparation sample, some uniaxial compressive tests are conducted on the frozen silty sand samples prepared with the mud sample preparation method. The failure strain and linear elastic modulus characteristics of frozen silty sand under uniaxial compression are investigated systemically in a wide range of strain rate and water content. The experimental results show that with rise of strain rate, failure strain increases gradually when water content is 12.0%; failure strain firstly increases and then decreases with growth of stain rate when water content is between 16.7% and 24.0%; when water content is greater than or equal to 30.6%, with increasing strain rate, failure strain decreases gradually; for the above three cases, the failure strain always tends gradually to be stable in the end. With increasing water content, failure strain firstly increases to a maximum sharply and then decreases dramatically. The failure strain tends to the failure strain of ice after water content is beyond 41.5%. Linear elastic modulus increases nonlinearly to a peak with increasing water content and then further rise of water content makes it lower, which can he described by a quadratic polynomial model. At - 2.0℃, when strain rate less than 4.67×10^-3 s^-1, with increase of water content, linear elastic modulus increases nonlinearly and then tends to the linear elastic modulus of ice; when strain rate greater than or equal to 4.67×10^-3 s^-1, linear elastic modulus firstly increases to a maximum and then decreases to the linear elastic modulus of ice with increase of water content. When temperature is at - 5.0℃, the similar critical value of strain rate to 4.67×10^3 s^-1 is 1.00× 10^2 s^-1.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.13