检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
机构地区:[1]大连交通大学土木与安全工程学院,辽宁大连116028 [2]大连理工大学建设工程学部,辽宁大连116024 [3]中国海洋大学工程学院,山东青岛266100
出 处:《建筑结构学报》2016年第8期76-81,共6页Journal of Building Structures
基 金:国家自然科学青年基金项目(51408093);国家自然科学基金重大国际合作项目(51261120375)
摘 要:为了剔除混凝土离散性的影响,利用电液伺服试验系统对同一钢筋混凝土柱进行不同加载速率下的往复加载试验。试验采用位移控制的加载模式,加载速率分别为0.2、40 mm/s。试验结果表明:构件的承载能力、刚度退化、承载力退化和累积耗能等力学性能均与加载速率直接相关。在加载速率为40 mm/s条件下,构件的承载能力、累积耗能均有提高,随着加载幅值的增加,加载速率的影响逐渐降低。刚度退化、承载力退化在快速加载条件下更为显著,随着加载速率的增加,软化台阶缩短,损伤进程加剧,构件延性降低,变形能力下降。在双向加载条件下,两个加载方向的耦联作用加速了构件的破坏进程,混凝土的开裂、钢筋屈服、混凝土脱落、纵筋屈曲均发生在更低的位移水平范围内,随着加载速率的提高,两水平加载方向的耦联作用进一步增强,构件变形能力明显降低。To eliminate the influence of concrete discreteness, quasi-static test of the same reinforced concrete (RC) column under different loading rates was carried out by the electro-hydraulic servo test system. The displacement- controlled loading, with loading rates of 0.2 mm/s and 40 mm/s, respectively, was adopted. The test results show that the mechanical properties of the specimen, such as the bearing capacity, stiffness degradation, bearing capacity degradation and cumulative energy dissipation, are directly related to the loading rate. The bearing capacity and cumulative energy dissipation of the specimens are improved under the loading rate of 40 mm/s. With the increase of the loading amplitude, the influence of loading rate gradually decreases. Stiffness degradation and bearing capacity degradation of the specimens are more significant under rapid loading. With the increase of loading rate, the softening stage is shortened with more obvious damage process. Besides, the ductility of the specimen and the deformation capacity are decreased. The coupling interaction of bi-direetional loading accelerates the failure process of the specimens. The cracking of the concrete, the buckling of the reinforcement bar, the spalling of the concrete and the yielding of the longitudinal reinforcement bar occur in the range of lower displacement level. With the increase of loading rate, the coupling interaction of bi-directional loading is further strengthened, and the deformation capacity of the specimen is obviously reduced.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.145