具有合理硬度梯度和组织分布的渗碳钢23CrNi3Mo的热处理冷却行为  

Cooling Behavior of Heat Treated Carburizing Steel 23CrNi3Mo with Proper Hardness Gradient and Microstructure Distribution

作　　者：蒋波[1] 戴光咏 闫永明[1] 刘广磊[2] 王芝林[2] 王国存[2] 刘雅政[1] 

机构地区：[1]北京科技大学材料科学与工程学院,北京100083 [2]西宁特殊钢股份有限公司,西宁810005

出　　处：《材料导报》2017年第8期70-75,共6页Materials Reports

基　　金：中央高校基本科研业务费(FRF-TP-16-032A1);中国博士后科学基金(2016M600915)

摘　　要：利用Gleeble-1500热模拟机、光学显微镜(OM)、扫描电镜(SEM)以及透射电镜(TEM)对渗碳钢23CrNi3Mo的连续冷却相变规律以及等温转变规律进行了研究,并基于此,设计了一种新的热处理冷却工艺。研究结果表明,渗碳后试样以0.05℃/s和0.1℃/s的冷速连续冷却时,表面渗碳层为高碳马氏体组织,过渡区为高碳马氏体+下贝氏体的混合组织,基体为下贝氏体组织;渗碳试样外表面在高温段以较低的冷速(0.05~3℃/s)连续冷却时,碳化物沿晶界析出形成网状碳化物;无渗碳的实验钢的贝氏体等温转变温度范围为375~450℃。新的热处理冷却工艺为:试样在880℃保温完成后,采用快速冷却工艺,以冷速大于等于5℃/s进入贝氏体转变温度区,直接入450℃的盐浴炉,入炉后均温5~10min,在低温转变区即贝氏体转变温度区间,采用慢速冷却工艺,冷速小于等于0.1℃/s。获得的试样渗碳层深度为1.4mm,国外的阿特拉斯钎头渗碳层深度为1.2mm,两者基本相同,但前者硬度分布更加平缓;两者表面显微组织均为高碳马氏体组织,过渡区均为马氏体加下贝氏体组织,基体均为贝氏体组织。通过设计新的热处理冷却工艺,获得了与国外钎头相同水平的试样。The continuous cooling transformation and isothermal transformation were investigated by thermal simulation ma- chine Gleeble-1500, optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscope （TEM）. Based on the investigation, a new heat treatment cooling process was designed. Results show that the microstructures at the surface, the transition zone and the matrix of the steel after carburizing at the cooling rates of 0. 05 ℃/s and 0. 1 ℃/s are high carbon mar- tensite, a mixed microstructure of lower bainite and high carbon martensite and lower bainite, respectively. The network carbide was formed along the boundary in the mierostructure at the surface when the earburizing steel was cooled from the quenching temperature with a lower cooling rate from 0. 05 ℃/s to 3 ℃/s. The temperature of bainite transformation of steel without carburizing ranges from 375 ℃ to 450 ℃. The new heat treatment cooling process was set as follow： the carburizing steel was cooled from 880 ℃ with a fast cooling rate of 5 ℃/s to the bainite transformation zone, and put into the salt bath furnace soaking for 5-10 minutes at 450 ℃; after that, the steel was slowly cooled at the cooling rate lower than 0. 1 ℃/s. Microstructural examination indicates that the depth of carburizing case of the specimen after the new process is 1.4 mm, which is nearly the same with the drill bit from Atlas a- broad （1.2 ram）. The hardness distribution of the specimen after the new process is smoother. The obtained mierostructures at the surface, the transition zone and the matrix of the specimen after the new process and the drill bit from Atlas abroad are both high car- bon martensite, a mixed microstructure of lower bainite and high carbon martensite and lower bainite, respectively. The earburizing steel which has a same level as the drill bit abroad was obtained by designing the new heat treatment cooling process.

关 键 词：渗碳钢 钎头 相变规律 冷速 下贝氏体 

分 类 号：TG335.5[金属学及工艺—金属压力加工]