高含水率木竹集成材刨切薄木(竹)表面粗糙度的测定与分析  

Surface roughness of high moisture content wood and bamboo laminated lumber sliced veneer(bamboo)

作　　者：于红卫[1] 刘志坤[1] 吕荣金 罗从军[1] 吕泽军 李光耀[1] 

机构地区：[1]浙江农林大学工程学院,浙江临安311300 [2]浙江升华云峰新材股份有限公司,浙江德清313220

出　　处：《浙江农林大学学报》2017年第4期711-720,共10页Journal of Zhejiang A&F University

基　　金：浙江省自然科学基金资助项目(Z3110223);浙江省重大科技专项重点农业项目(2015C02029)

摘　　要：将新采伐的小径级杉木Cunninghamia lanceolata,马尾松Pinus massoniana,樟树Cinnamomum camphora(复合用)和毛竹Phyllostachys edulis(含水率均在纤维饱和点以上)制成具有一定规格尺寸、高含水率的集成木(竹)方材,经刨切加工得到薄木(竹),再气干至含水率15%左右,通过触针法对未作砂光处理的薄木(竹)正面表面粗糙度进行测定。结果表明:刨切薄木表面粗糙度值的大小与材质、纹理方向及指榫显著相关(P<0.05),刨切薄竹与竹节无明显相关,与白梧桐Triplochitin scleroxylon,紫椴Tilia amurensis科技木刨切薄木相比,差异不显著(P>0.05),可满足各类基材贴面的质量要求。China, a developing country with comparatively meager timber resources and with natural, precious,and high-quality wood that is becoming scarcer, has produced various artificial veneers imitating the color and grain of precious wood using small-diameter and low-quality timber, which in turn has become an important way to replenish natural decorative veneer resources. Wood timber and bamboo squares fabricated by freshlyfelled timber（green timber） finger-joint widened and thickened was sliced directly into wood or bamboo veneers, to not only simplify the manufacturing technique, but also to save on production costs and to increase economic benefits. Freshly-felled Cunninghamia lanceolata, Pinus massoniana, and Cinnamomum camphora with moisture content above the fiber saturation point were first, sawed into sheets or lumber; second, transversely truncated into wood blocks without knots; and third, made into combination unit or bamboo cane billets. Next,newly logged Phyllostachys edulis was cut longitudinally and planed roughly into bamboo cane billets. These bamboo cane billets were then smoothly planed and glued by polyurethane rubber and mixed glues. Finally they were widened and thickened into predetermined sizes, wood timber： 2 550 mm × 670 mm × 450 mm; and bamboo squares： 2 550 mm × 670 mm × 485 mm depending on actual production demand. The high moisture content laminated wood timber and bamboo squares used a cold-press gluing process. These were then sliced into wood or bamboo veneer. To determine whether the wood or bamboo veneers fabricated by this new technology met follow-up processing requirements, surface roughness was tested when the air-dried moisture content was about 15% and measured by the stylus tracing method. Results showed that surface roughness of high moisture content wood and bamboo laminated lumber sliced veneer and bamboo could meet the quality requirements of various base material veneers with a strong relationship to the material, grain direction, and finger-joints; but not to

关 键 词：木材科学与技术 高含水率木(竹)材 集成材 刨切薄木(竹) 表面粗糙度 

分 类 号：S781.6[农业科学—木材科学与技术]