光纤放大器放大自发辐射特性与高温易损点位置  

Amplified spontaneous emission characteristics and locations of high temperature vulnerable point in fiber amplifiers

作　　者：罗亿[1] 王小林[1] 张汉伟[1] 粟荣涛[1] 马鹏飞[1] 周朴[1] 姜宗福[1] 

机构地区：[1]国防科学技术大学光电科学与工程学院,高能激光技术湖南省重点实验室,大功率光纤激光湖南省协同创新中心,长沙410073

出　　处：《物理学报》2017年第23期171-184,共14页Acta Physica Sinica

基　　金：国家自然科学基金(批准号:61505260,61735007)资助的课题~~

摘　　要：在高功率光纤放大器实验中,时常发现增益光纤抽运注入熔接点后10—50 cm处容易发生光纤烧毁现象.为了对该现象进行理论预测,基于光纤激光器速率方程模型和增益光纤的热传导模型,从种子功率、抽运功率和抽运吸收三个方面对掺镱双包层光纤放大器中的放大自发辐射(ASE)和温度特性进行研究.结果表明,在放大倍率较高、ASE较为严重等情况下,光纤放大器中的最高温度点一般不在抽运注入的熔接点处,而在距离熔接点10—50 cm处,与实验中发现光纤烧毁的位置基本符合.从光纤放大器的ASE抑制、最高温度点温度控制角度出发,对光纤放大器在种子功率、抽运功率、抽运吸收、放大倍率和抽运波长等方面的设计给出了指导性的建议.Master oscillator power amplifier （MOPA） is a common configuration in fiber lasers to obtain high power output. Amplified spontaneous emission （ASE） is amplified stage by stage by MOPA, which may result in damage to the fiber amplifier. In the experiment of high-power fiber amplifier, thermal effect is one of the most critical issues. High temperature from significant thermal effect would restrict the further improvement of laser power and cause the fiber to damage. In most of the experiments, the gain fibers are broken usually at the place 10-50 cm away from the fused point of the pump injection end. To better understand in physics the highest temperature and the position of the burning point, we study the ASE and temperature characteristics by using the rate equation model of fiber laser and the thermal conduction model of gain fiber. We analyze the influences of seed power, pump power and pump absorption on Yb-doped double-cladding fiber amplifier. The results show that when magnification is relatively high and ASE is serious, the highest temperature point of the fiber amplifier is not at the fused point of the pump injection end but at the place 10-50 cm away from the fused point, which consists well with the experimental result. For studying the ASE suppression and the temperature control of the hottest point, we compare the three parameters in the 915 nm pumped case with those in the 975 nm pumped case, these being power ratio of ASE to the output laser, hottest location along the fiber, and the ratio of the temperature difference between the highest temperature and fusion point temperature to the latter one. It is concluded that the optimal parameters for the 915 nm pumped case are seed power larger than 7 W, pump power less than 1250 W, and pump absorption less than 20 dB. As to the 975 nm pumped case, it is suggested that the seed power should be not less than 8 W with an appropriate pump power. The research also implies that a better performance of fiber amplifier is pumped by 975 nm under the s

关 键 词：光纤放大器 放大自发辐射 温度特性 

分 类 号：TN722[电子电信—电路与系统]