微纳结构超疏水表面的浸润性分析及设计  

Wettability Analysis and Design of Micro-nanostructured Superhydrophobic Surface

作　　者：马国佳[1] 郑海坤[2] 常士楠[2] 王硕硕 Ma Guojia;Zheng Haikun;Chang Shinan;Wang Shuoshuo(Science and Technology on Power Beam Processes Laboratory, Beijing Aeronautical Manufacturing Technology Research Institute, Beijing 100024;School of Aeronautic Science and Engineering, Beihang University, Beijing 100191)

机构地区：[1]北京航空制造工程研究所高能束流加工技术国家重点实验室北京100024 [2]北京航空航天大学航空科学与工程学院北京100191

出　　处：《化学学报》2019年第3期269-277,共9页Acta Chimica Sinica

基　　金：国家自然科学基金(Nos.11672024,11372026);国家重点基础研究发展计划项目(No.2015CB755803)资助~~

摘　　要：微纳复合结构超疏水表面在防污、流动减阻、防冰等领域具有广阔的应用前景,超疏水表面主要通过设计表面化学性质和微观几何结构来获得.合理设计保持表面润湿态的稳定性是其性能发挥的关键.以"液滴-超疏水表面"系统为研究对象,基于最小能原理分析了四种稳定润湿形态,指出影响润湿状态的本征接触角和微观结构参数(相对柱距、相对柱高).推导了本征接触角的计算公式并对常见材料的本征接触角进行了讨论.结合四种润湿态方程,绘制了随着相对柱距和相对柱高的润湿云图,并将润湿云图归纳为"一点三线六区四状态".分析了相对柱距和相对柱高对浸润状态的影响,结果表明较大的本征接触角、较小的相对柱距和较大的相对柱高能够减小浸润状态发生转变的临界参数,从而拓展超疏水表面的区域范围,有利于超疏水表面的稳定性.利用文献数据验证了上述润湿云图能够准确反映出润湿形态.在上述工作基础之上总结提炼了超疏水表面设计的一般思路.研究结果可为超疏水表面的设计提供理论依据和技术基础.The special wettability of superhydrophobic surface usually has high contact angles (CA>150°) and low contact angle hysteresis (CAH<5°), which has been exploited for many potential applications. It is well known that wettability is mainly determined by micro/nano structure and surface composition, and various types of natural superhydrophobic surface could exhibit different wetting states, showing different wetting properties, such as low adhesive lotus leaf;the anisotropic superhydrophobic rice leaf;high adhesive rose petal. Therefore, the relationship between the wetting state and the surface structure should have a deeper understanding, especially in the design preliminary stage. The "droplet-superhydrophobic surface" system is taken as the research objects, four stable wetting state expressions are analyzed based on the principle of minimum energy. Wetting state transitions are studied on superhydrophobic surface coverd with micro/nano structured pillars of different distributions. The calculation formula of intrinsic contact angle is derived and the intrinsic contact angle of common materials is investigated. Based on the four wetting state of apparent contact angle equations, wetting diagrams were drew for investigating the wetting behavior, which include "one point, three lines, six areas, four state". The influence of the relative structure spacing and relative structure height on the wetting state is analyzed. It is found that the larger relative structure height, the smaller relative structure spacing, which can reduce the critical parameters of the transition state of the infiltration state, thereby expanding the range of the superhydrophobic surface, the more design options are available. It is also beneficial to the stability of the superhydrophobic surface, but should be controlled within certain scales because of mechanical stability. The simulation results accurately reflect the wetting state with the changes of the relative structure spacing and relative structure height. Finally, the general d

关 键 词：浸润性 微纳结构表面 临界相对柱距 临界相对柱高 设计思路 润湿状态转变 

分 类 号：O647.5[理学—物理化学]