纳米流体微量润滑铣削Ti-6Al-4V冷却性能实验评价  

Analysis on Cooling Performance of Ti-6Al-4V in Minimal Quantities Lubricant Milling with Different Nanoparticles

作　　者：董兰[1,2] 柏秀芳 李长河 翟明戈[1,2] 齐强[1,2] 吕晓杰[1,2] 殷庆安[3] 李莉芳 张峰标[4] DONG Lan;BAI Xiu-fang;LI Chang-he;ZHAI Ming-ge;QI Qiang;LV Xiao-jie;YIN Qing-an;LI Li-fang;ZHANG Feng-biao(Research and Development Center of Mechanical and Electrical Engineering Technology in Shandong University,Qingdao Binhai University,Qingdao Shandong 266555,China;College of Mechanical and Electrical Engineering,Qingdao Binhai University,Qingdao Shandong 266555,China;School of Mechanical and Automotive Engineering,Qingdao University of Technology,Qingdao Shandong 266520,China)

机构地区：[1]青岛滨海学院山东省高等学校机电工程技术研发中心,山东青岛266555 [2]青岛滨海学院机电工程学院,山东青岛266555 [3]青岛理工大学机械与汽车工程学院,山东青岛266520 [4]青岛海内环保科技有限公司,山东青岛266555

出　　处：《组合机床与自动化加工技术》2019年第7期151-155,共5页Modular Machine Tool & Automatic Manufacturing Technique

基　　金：国家自然科学基金项目青年基金(51806112);山东省高等学校科研发展计划项目(J17KB016,J18KA017);青岛滨海学院科技计划研究项目(2017KZ03)

摘　　要：利用纳米粒子的强化换热能力,将纳米粒子加入基础油形成的纳米流体,能够解决仅基础油的微量润滑铣削冷却能力不足的问题,深入研究不同纳米粒子+基础油的纳米流体微量润滑的冷却效果,文章对不同纳米粒子微量润滑铣削时的冷却效果进行实验评价。以Ti-6Al-4V作为工件材料,棉籽油作为微量润滑基础油,6种不同纳米粒子(Al2O3、MoS2、SiO2、CNTs、SiC、Graphite)以1.5%的质量比用二步法配置成的纳米流体进行微量润滑铣削,通过铣削力、铣削工件瞬时温度、表面粗糙度值及表面微观形貌进行实验评价,实验结果表明SiO2纳米粒子铣削时铣削力比较大,但铣削时工件的温度是最低的,说明SiO2纳米粒子的冷却能力在这些纳米粒子中是最强的,SiO2和Al2O3纳米流体铣削工件的温度不仅能快速降下来,并且温度降的比较低,同时Al2O3和SiO2纳米粒子都能达到较好的表面粗糙度值,加入Al2O3纳米粒子的表面粗糙度值比纯棉籽油降低了66.7%。The enhanced heat transfer capacity of nanoparticles was used,nanofluids was formed by adding nanoparticles to the base oil,It was possible to solve the problem of insufficient cooling capacity of micro lubricating oil milling of base oil only,It was deeply investigate that cooling effect of microlubricity of nano-fluid of different nanoparticles + base oil.In this paper,the cooling effects of MQL milling with different nanoparticles were evaluated experimentally.Using Ti-6Al-4V as workpiece material and with Cotton-seed oil ACTS as the base oil for MQL,six different nanoparticles were used for MQL milling with a mass ratio of 1.5% to the configured nano fluids,performing laboratory evaluation through milling force,instantaneous temperature of that milling work,surface roughness value and surface micro topography.The experimental results show that the milling force of SiO 2 nanoparticles was relatively large,but the temperature of the workpiece was the lowest when milling,which indicates that the cooling capacity of SiO2 nanoparticles was the strongest among these nanoparticles.The temperature of SiO2 and Al2O3 nanometer fluid milling workpiece can not only decrease rapidly,but also falls to a relatively low point.At the same time,Al2O3 and SiO 2 nanoparticles can achieve a better surface roughness value.The surface roughness value of the nanoparticle added into the Al2O3 was reduced by 66.7% compared with pure cottonseed oil.

关 键 词：纳米粒子 微量润滑 铣削 冷却效果 

分 类 号：TH16[机械工程—机械制造及自动化] TG547[金属学及工艺—金属切削加工及机床]