基于D-P准则有压圆形衬砌隧洞弹塑性解  

D-P Yield Criterion Based Elastoplastic Solution of the Circular Pressure Tunnel

作　　者：王睢 钟祖良[3] 刘新荣[3] 吴波 赵勇博[1,2] 李占涛 WANG Sui;ZHONG Zuliang;LIU Xinrong;WU Bo;ZHAO Yongbo;LI Zhantao(School of Civil and Transportation Engineering,Ningbo University of Technology,Ningbo 315211;The Soft Soil Research Center in Ningbo University of Technology,State Key Laboratory of Geomechanics and Geotechnical Engineering,Ningbo 315211;School of Civil Engineering,Chongqing University,Chongqing 400045;College of Civil Engineering and Architecture,Guangxi University,Nanning 530004)

机构地区：[1]宁波工程学院建筑与交通工程学院,宁波315211 [2]岩土力学与工程国家重点实验室宁波工程学院工程软土实验中心,宁波315211 [3]重庆大学土木工程学院,重庆400045 [4]广西大学土木建筑工程学院,南宁530004

出　　处：《现代隧道技术》2019年第4期74-80,共7页Modern Tunnelling Technology

基　　金：国家自然科学基金项目(51108485,51678164,51808083);广西自然科学基金项目(2018GXNSFDA138009);浙江省自然科学基金项目(LY16E040002);宁波市公益类科技计划项目(2019C50012)

摘　　要：随着大型水利工程的建设,出现了大量的深埋水工压力隧洞。由于深埋有压隧洞在施工和运营不同工况条件下,隧道衬砌和围岩主应力会发生变化。文章基于D-P屈服准则,在平面应变条件下推导了深埋有压衬砌圆形隧洞第一主应力分别为径向应力和切向应力时隧洞的弹塑性解。研究结果表明:该理论模型计算值与M-C准则计算值基本吻合,验证了该模型的正确性,且较M-C准则计算结果偏于安全;在不同地应力水平与内水压力工况下,衬砌与围岩的塑性区半径发生变化;随着内水压力的增大,塑性区分布可分为5个阶段,且在高水压阶段水压力增大对衬砌屈服半径的发展较为迅速。With the construction of large-scale water conservancy projects in China, many deep-buried hydraulic pressure tunnels have been built. The principal stress of tunnel lining and surrounding rock will be changed under different conditions of construction and operation for the deep buried pressure tunnel. Based on D-P yield criterion,the elastoplastic solution of the deep-buried circular pressure tunnel was derived when the first principal stress is the radial stress or tangential stress under the condition of plane strain. The research shows that the calculated values by this model were consistent with the calculated values by M-C criterion, which verifies the correctness of this model and it is more conservative compared with the calculated results by M-C criterion;radiuses of plastic zones of lining and surrounding rock will change in different stresses levels and internal water pressures;plastic zone distribution can be divided into five stages and the yield radius of lining develops faster with an increase of internal water pressure during high water pressure stage.

关 键 词：水工隧洞 D-P准则 弹塑性解 第一主应力 深埋 有压衬砌 圆形隧洞 

分 类 号：U452[建筑科学—桥梁与隧道工程]