检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:严喜林 张怿宁 崔鹏飞 国建宝 杨光源 YAN Xilin;ZHANG Yining;CUI Pengfei;GUO Jianbao;YANG Guangyuan(EHV Maintenance&Test Center of China Southern Power Grid,Guangzhou 510663,China)
机构地区:[1]中国南方电网有限责任公司超高压输电公司检修试验中心
出 处:《电力电容器与无功补偿》2019年第6期140-145,共6页Power Capacitor & Reactive Power Compensation
基 金:中国南方电网有限责任公司科技项目(CGYKJXM00000028)
摘 要:换流阀冷却系统是高压直流输电系统的重要设备,为避免晶闸管PN结温度过高导致换流阀损坏,配置有进阀温度保护。结合晶闸管换流阀损耗计算原理,推导出晶闸管换流阀结温计算公式,并提出了一种考虑晶闸管损耗计算误差的结温计算修正公式。在此基础上,系统地提出了阀冷却系统进阀温度保护定值整定方法。该方法通过结温计算修正公式计算晶闸管最高允许结温,反向推导出最大允许进阀温度,从而确定阀冷系统进阀温度保护定值。通过对南方电网鲁西换流站进阀温度保护定值整定进行算例分析,验证了该方法的有效性。该方法已在南方电网鲁西站、金官站现场应用,效果良好,可为后续新建直流工程阀冷系统保护设计及定值整定提供参考。Converter valve cooling system is an important equipment of HVDC transmission system.For avoiding damage of the converter valve due to high PN junction temperature of the thyristor,it is equipped with inlet valve temperature protection.The formula for calculating the junction temperature of thyristor valve is derived in combination of the loss calculation principle of thyristor valve and a kind of calculation and correction formula of junction temperature considering loss calculation error of thyristor.On this basis,the protection setting method of the inlet valve of the valve cooling system is systematically proposed.This method calculates the permissible maximum junction temperature of the thyristor and reversely deduces the maximum allowable inlet valve temperature through junction temperature calculation and correction formula,so to determine the temperature protection setting of the inlet valve of the valve cooling system.The effectiveness of the method is verified by an example analysis of the setting of the temperature protection of the incoming valve of Luxi converter station of southern power grid.This method has been applied in the field of Luxi station and Jinguan station of southern power grid with good result,which can provide reference for protection design and setting of valve cooling system fomewproject.
关 键 词:高压直流输电 换流阀冷却系统 结温计算 进阀温度保护 定值整定
分 类 号:TM7[电气工程—电力系统及自动化]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.28