锡林刺辊速比对梳棉质量的影响  

Effect of speed ratio between cylinder and taker-in on carding quality

作　　者：邵英海[1,2] 张明光[1,2] 曹继鹏[1,2] 郭昕[1] 韩贤国[2,3] SHAO Yinghai;ZHANG Mingguang;CAO Jipeng;GUO Xin;HAN Xianguo(School of Clothing and Textile,Eastern Liaoning University,Dandong,Liaoning 118003,China;Key Laboratory of Functional Textile Materials,Liaoning Province,Eastern Liaoning University,Dandong,Liaoning 118003,China;School of Mechanical and Electrical Engineering,Eastern Liaoning University,Dandong,Liaoning 118003,China)

机构地区：[1]辽东学院服装与纺织学院,辽宁丹东118003 [2]辽东学院辽宁省功能纺织材料重点实验室,辽宁丹东118003 [3]辽东学院机械电子工程学院,辽宁丹东118003

出　　处：《纺织学报》2020年第1期39-44,共6页Journal of Textile Research

基　　金：2018年辽宁省高等学校创新人才支持计划项目(2018478);辽宁省自然科学基金项目(2019-MS-148)

摘　　要：为提高棉花梳理质量,针对多种刺辊速度条件下锡林刺辊速比变化对生条、一并条和二并条质量的影响进行对比实验。探讨锡林刺辊速比变化对棉纤维梳理质量的影响,并通过SPSS统计软件对生条、一并条和二并条的质量参数进行相关性分析。实验结果表明:刺辊速度在500~800 r/min之间时,生条、一并条和二并条中的长度相关指标变化幅度较小,即使在同一刺辊速度不同锡林刺辊速比条件下,其变化幅度依然较小,但棉结和杂质含量随刺辊速度和锡林刺辊速比的增加,均呈现明显下降趋势;当刺辊速度为850~900 r/min时,长度指标随着刺辊速度和锡林刺辊速比的增加均出现较明显的降低,棉结和杂质含量出现明显增加趋势。生条、一并条和二并条之间的大多数指标存在较高的相关性。To improve cotton carding quality,the effect of speed ratio between cylinder and taker-in on card sliver,breaker sliver and intermediate sliver were investigated under different speeds of cylinder and taker-in.The parameter correlation between card sliver and breaker sliver,intermediate sliver was analyzed using SPSS.The results showed that when the taker-in speed ranges from 500 r/min to 800 r/min,the length-related parameters changed a little,even under the same taker-in speed with different speed ratios.However,the numbers of nep and impurities had an obvious decreasing tendency with the increase of taker-in speed and cylinder/taker-in speed ratio.In the case when the taker-in speed is in the range of 850 to 900 r/min,the length-related parameters decreased and the numbers of nep and impurities increased remarkably with the increase of taker-in speed and cylinder/taker-in speed ratio.

关 键 词：锡林速度 锡林刺辊速比 棉条质量 梳棉机 

分 类 号：TS104.2[轻工技术与工程—纺织工程]