检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:李春利[1,2] 李景玉 张明霞 LI Chunli;LI Jingyu;ZHANG Mingxia(School of Chemical Engineering and Technology,Hebei University of Technology,Tianjin 300130,China;National-Local Joint Engineering Laboratory for Energy Conservation in Chemical Process Integration and Resources Utilization,Tianjin 300130,China)
机构地区:[1]河北工业大学化工学院,天津300130 [2]化工节能过程集成与资源利用国家地方联合工程实验室,天津300130
出 处:《化工学报》2020年第4期1460-1468,共9页CIESC Journal
基 金:国家重点研发计划项目(2017YFB0602500);中央引导地方科技发展专项(19944507G)。
摘 要:在填料塔三参数壁流模型的基础上,提出了应用于隔壁塔半圆型填料层的壁流模型。通过实验对模型参数进行了估计。模型计算值与实验值吻合较好。在内径为580 mm、高2800 mm的半圆冷模塔内,常温常压下以空气-水为介质,测取了散堆填料的壁流曲线,分析了气液速率变化对壁流的影响。以氯化钠溶液为示踪剂,通过脉冲注入扰动响应技术获得停留时间分布曲线。发现气液速率变化均对停留时间分布产生不同程度影响。同时比较了同一填料层高度塔壁区和整体区的平均停留时间,在壁流充分发展阶段,塔壁区的平均停留时间明显小于整体区。从另一方面量化了壁流效应的影响。应用线性回归得到单相流和气液逆流时计算Pe d的关联式。对于新型填料及塔内件的开发、改进隔壁塔的设计方法,从而实现安全有效放大具有参考意义。Based on the three-parameter wall flow model of the packed tower,a wall flow model applied to the semi-circular filler layer of the dividing wall tower is proposed.Refer to experimental data,the model parameters were estimated.The results agree well with the theoretical value.A set of semicircular cold test system with a diameter of 580 mm and a height of 2800 mm was built,and the effect of gas and liquid rate change on the wall flow was analyzed.The residence time distribution(RTD)curves were obtained by pulse injection stimulus-response technique.It is found that the RTD is affected by the change of gas and liquid rate.The influence of wall flow effect is quantified by the average residence time comparison between wall section and bulk section,the results show that the average residence time of wall section was smaller than that of bulk section at the wall flow full development stage.Such data are essential for design and optimization of dividing wall column distillation processes.Correlation of Pe d is calculated by liner regression.This experiment has reference significance for the development of new packings,inner parts and the improvement of the design method of DWC to achieve safe,reliable and effective amplification.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.119