检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:康磊 张肖男 娄建军 强亮亮 KANG Lei;ZHANG Xiao-nan;LOU Jian-jun;QIANG Liang-liang(Tsinghua Innovation Center in Dongguan,Dongguan,China,523808;No.703 Research Institute of CSIC,Harbin,China,150078;Jiangsu Luhang Power Technology Co.Ltd.,Nanjing,China,211113)
机构地区:[1]清华东莞创新中心,广东东莞523808 [2]中国船舶重工集团公司第七〇三研究所,黑龙江哈尔滨150078 [3]江苏禄航动力科技有限公司,江苏南京211113
出 处:《热能动力工程》2020年第3期158-166,共9页Journal of Engineering for Thermal Energy and Power
基 金:东莞市引进创新科研团队计划(2014607101)。
摘 要:考虑气体温度梯度对工质物性及轴承热稳定性的影响,以及润滑气体和多孔介质的传热耦合,在满足Darcy定律条件下三维求解雷诺方程,计算了轴承间隙和多孔介质中气体的压力及温度分布。分析了3个给定供给压力(0.5、0.65和0.8 MPa)、3种轴承偏心率(0.2、0.5、0.8)对轴承的承载能力、偏位角及润滑流量的影响,计算结果表明:在不同的轴偏心率下均存在有一段轴承最佳渗透系数范围,表征该范围承载能力最强;偏心率越大,轴承承载能力越高,最佳渗透系数区间也越明显;轴承压缩数越大承载能力也越高;间隙中温度分布不均匀导致轴承承载能力降低,通过调整压力和偏心率增加介质的润滑流量,及时导出摩擦产生热量降低间隙中气膜温度,可使轴承平衡稳定运行。Porous media bearing has been widely used for its high load capacity and static and dynamic characteristics.This paper considers the influence of temperature gradient on bearing characteristics and solves the Reynolds equation in three-dimensions under the condition of Darcy’s law.The pressure distribution in the bearing gap and porous media is calculated.Since the temperature of the lubricating medium affects the physical properties,the heat transfer coupling between the lubricating gas and the porous medium is considered.The effects on the bearing characteristics from different pressures,different eccentricities,and different temperature conditions are investigated.The calculation results shows: there is a range of optimal feeding parameter for bearing load capacity under different eccentricities;the greater the eccentricity,the higher the bearing capacity,and the more noticeable the optimal feeding parameter interval.The larger bearing number of bearing,the higher the capacity.As the temperature increases,the viscosity decreases,and the temperature distribution in the gap is non-uniform,which causes the bearing load to decrease.By adjusting the pressure and eccentricity,the lubrication flow rate of the medium is increased,and the film temperature is lowered,leading to stable operation of the bearing.
分 类 号:TH133.3[机械工程—机械制造及自动化]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.249