工业建筑新型全螺栓装配式设备支架的设计与减震措施研究  

Design and Seismic Vibration Control Measures of a Novel Prefabricated Equipment Support with Fully Bolted Connections for Industrial Buildings

作　　者：李刚[1,2,3] 刘笑天 王伟 李俊霖[1,2] LI Gang;LIU Xiaotian;WANG Wei;LI Junlin(State Key Laboratory of Disaster Reduction in Civil Engineering,Tongji University,Shanghai 200092,China;College of Civil Engineering,Tongji University,Shanghai 200092,China;CNNC Seventh Research and Design Institute Co.,Ltd.,Taiyuan 030012,China)

机构地区：[1]同济大学,土木工程防灾国家重点实验室,上海200092 [2]同济大学土木工程学院,上海200092 [3]中核第七研究设计院有限公司,太原030012

出　　处：《建筑钢结构进展》2020年第6期21-28,共8页Progress in Steel Building Structures

基　　金：“十三五”核能开发科研第三批项目(000006)。

摘　　要：针对工业建筑在役设备支架中存在的现场施焊环境污染以及无专门抗震设计规范可循等诸多问题,提出了基于《建筑抗震设计规范》的特定抗震性能目标,即保持结构处于"中震弹性"状态下,支架各挂机点水平加速度不超过设备限值。通过对比无控状态、TMD控制状态、无阻尼TMD控制状态下全螺栓装配式钢支架结构的动力响应,分析了设备支架采取振型分解反应谱法及非线性时程分析下的抗震性能与振动控制效果。结果表明:设防烈度不超过8度(0.20g)时,设备支架保持弹性状态;在支架顶部设置参数合理的TMD及无阻尼TMD装置,可以有效降低设备支架各挂机点加速度,其中,可在8度(0.20g)、7度(0.15g)、7度(0.10g)设防烈度下,分别选用TMD控制、无阻尼TMD控制、无控状态下的设备支架。A specific seismic performance goal based on the Code for Seismic Design of Buildings is proposed,which addresses many issues of welding pollution in an existing equipment support for industrial buildings.Currently there are no special seismic design code to follow,which maintains the structure in elastic state under moderate earthquake,and controls the horizontal acceleration within equipment limits.Through the comparison of dynamic response of prefabricated steel frame with fully bolted connections under the uncontrolled condition,TMD control state and TMD without damper control state,the seismic performance and control effect of the equipment support are analyzed using response spectrum method and nonlinear time-history analysis.The results show that the equipment support remains elastic when the fortification intensity will not exceed 8 degree(0.20g);The TMD and TMD without damper devices with reasonable parameters set on the top of the support can effectively reduce the acceleration of the hanging points,among which TMD control,TMD without damper control and uncontrolled device supports can be selected respectively under the fortification intensity of 8 degree(0.20g),7 degree(0.15g)and 7 degree(0.10g).

关 键 词：全螺栓装配式钢框架 设备支架 TMD装置 无阻尼TMD装置 振动控制 反应谱法 非线性时程分析 

分 类 号：TU352.1[建筑科学—结构工程]