搅拌头转速对2507双相不锈钢搅拌摩擦加工组织及性能的影响  

Effect of Tool Rotation Speed on Microstructure and Properties of Friction Stir Processed 2507 Duplex Stainless Steel

作　　者：陈果[1,2] 王新波 张仁晓[1,2] 马成悦 杨海峰 周利 赵运强[3] CHEN Guo;WANG Xinbo;ZHANG Renxiao;MAChengyue;YANG Haifeng;ZHOU Li;ZHAO Yunqiang(State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology,Harbin 150001,China;Shandong Provincial Key Laboratory of Special Welding Technology,Harbin Institute of Technology at Weihai,Weihai 264209,China;Guangdong Provincial Key Laboratory of Advanced Welding Technology,China-Ukraine Institute of Welding,Guangdong Academy of Sciences,Guangzhou 510651,China)

机构地区：[1]哈尔滨工业大学先进焊接与连接国家重点实验室,哈尔滨150001 [2]哈尔滨工业大学(威海)山东省特种焊接技术重点实验室,威海264209 [3]广东省科学院中乌焊接研究所广东省现代焊接技术重点实验室,广州510651

出　　处：《金属学报》2021年第6期725-735,共11页Acta Metallurgica Sinica

基　　金：山东省重大科技创新工程项目No.2017CXGC0811;广州市科技计划项目No.201704030038。

摘　　要：通过对5 mm厚2507双相不锈钢进行搅拌摩擦加工,研究了在加工速率为100 mm/min时搅拌头转速对加工区域组织、力学性能和腐蚀性能的影响。结果表明,随着搅拌头转速的增大,搅拌区晶粒尺寸呈现先减小后增大的趋势。加工热循环和应力变形对加工区铁素体与奥氏体组织比例的变化影响不大,其铁素体含量仍保持在标准规范40%~60%之间。仅在搅拌头转速为200 r/min时,在加工区底部发现σ相析出。加工区显微硬度分布呈现“盆状”,其硬度最高值出现在搅拌区前进侧的底部,对应搅拌区晶粒尺寸最细小处。随着搅拌头转速的增加,搅拌区纵向拉伸强度呈现先增大后减小的趋势,而塑性则呈现先减小后增大的趋势。搅拌头转速为400 r/min时,搅拌区具有最优腐蚀性能。Duplex stainless steel with its exceptional corrosion resistance,mechanical properties,and proficient weldability has been widely used in ships and bridges,as well as petrochemical and seawater desalination industries.Friction stir processing(FSP)does not only induce dynamic recrystalliza-tion of the material but also achieves the purpose of repairing the crack automatically,which markedly improves the mechanical properties of duplex stainless steel.Thus,FSP is particularly useful for crack repair of duplex stainless steel structures.In the present study,microstructure,mechanical property,and corrosion property of FSP 2507 duplex stainless steel were investigated.FSP was performed at a constant welding speed of 100 mm/min and tool rotation speeds of 200,300,400,500,and 600 r/min using a tungsten-rhenium-based tool.Due to the thermal and mechanical effects in the processing,the section of the processing zone can be divided into the thermo-mechanically affected zone(TMAZ)and the stir zone(SZ).Only under the sufficient parameters of thermoplastic flow,the internal faultless processing zone was obtained.In accordance with the increased tool rotating speed,the grain size of the SZ initially decreased and then increased.Processing heat cycle and stress deformation had an insignificant influence on the proportion of ferrite and austenite phases in the processing zone,and the ferrite content still remained between 40%and 60%in the standard specification.Theσphase was determined at the bottom of the processing zone,namely at the tool rotation speed of 200 r/min due to the low heat input.Microhardness distribution of the processing zone demonstrated a basin-like morphology,and the largest hardness value appeared at the bottom of the advanced side of the SZ,corresponding to the smallest grain size of the SZ.As the tool rotating speed increased,the longitudinal tensile strength of the SZ increased initially and then decreased,contrary to the elongation.According to the results of potentiometric polarization and electrochemi

关 键 词：双相不锈钢 搅拌摩擦加工 析出相 力学性能 腐蚀性能 

分 类 号：TG453.9[金属学及工艺—焊接]