塑性变形对2024铝合金拼焊接头腐蚀性能的影响  

Influence of plastic deformation on corrosion performance for 2024 aluminum alloy tailored welded joint

作　　者：赵满 孙倩[1,2] 庞秋[3] 胡志力[1,2,4] Zhao Man;Sun Qian;Pang Qiu;Hu Zhili(Hubei Key Laboratory of Advanced Technology for Automotive Components,Wuhan University of Technology,Wuhan 430070,China;Hubei Collaborative Innovation Center for Automotive Components Technology,Wuhan University of Technology,Wuhan 430070,China;School of Mechanical and Electrical Engineering,Wuhan Donghu University,Wuhan 430212,China;Hubei Research Center for New Energy&Intelligent Connected Vehicle,Wuhan University of Technology,Wuhan 430070,China)

机构地区：[1]武汉理工大学现代汽车零部件技术湖北省重点实验室,湖北武汉430070 [2]武汉理工大学汽车零部件技术湖北省协同创新中心,湖北武汉430070 [3]武汉东湖学院机电工程学院,湖北武汉430212 [4]武汉理工大学湖北省新能源与智能网联车工程技术研究中心,湖北武汉430070

出　　处：《锻压技术》2022年第3期198-205,共8页Forging & Stamping Technology

基　　金：国家自然科学基金资助项目(51775397);湖北省重点研发计划项目(2020BAB140);武汉市科技成果转化专项(2019030703011511);湖北省教育厅科学研究计划项目(B2020245)。

摘　　要：为研究变形程度对铝合金搅拌摩擦焊(FSW)接头腐蚀性能的影响规律。采用单向拉伸试验,通过Tafel极化曲线及剥落腐蚀试验研究不同程度的塑性变形量对2024铝合金FSW接头焊核腐蚀性能的影响,利用金相显微镜(OM)、扫描电镜(SEM/EDS)等观察得到的显微组织来表征试验结果并分析其影响腐蚀性能的机理。结果表明:在变形量为0%、4%、7%和10%的塑性变形中,耐腐蚀性依次为:变形量为0%的试样>变形量为7%的试样>变形量为10%的试样>变形量为4%的试样,在塑性变形量为7%处出现“拐点”。随着塑性变形量的增大,位错及位错环增多,包围缠绕的析出相增多,耐腐蚀性随之提高;但大的变形会使塑性变形量为10%的试样上出现微裂纹,容易被腐蚀,导致耐腐蚀性有所下降。In order to study the influence laws of deformation degree on the corrosion performance of friction stir welding(FSW)joint for aluminum alloy,using uniaxial tensile tests,the influences of plastic deformation amount in different degrees on the corrosion performance of 2024 aluminum alloy FSW joint were studied by Tafel polarization curve and exfoliation corrosion test,and the test results were characterized by the microstructures observed by optical microscope(OM)and scanning electron microscope(SEM/EDS)to analyze the mechanism of its influence on the corrosion performance.The results show that in the plastic deformation amount of 0%,4%,7%and 10%,the corrosion resistance performance of FSW joint is as follows:the sample with deformation of amount 0%>the sample with deformation of amount 7%>the sample with deformation amount of 10%>the sample with deformation amount of 4%.An“inflection point”appears at the plastic deformation amount of 7%.With the increasing of plastic deformation amount,the number of dislocations and dislocation rings increases,the number of precipitation phases surrounding and winding increases,and the corrosion resistance performance also increases.However,large deformation causes micro-cracks on the sample with plastic deformation amount of 10%,which is easy to be corroded,resulting in a decrease in the corrosion resistance performance.

关 键 词：塑性变形 2024铝合金 搅拌摩擦焊 拼焊接头 微观结构 腐蚀性能 

分 类 号：TG146.2[一般工业技术—材料科学与工程]