检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:刘炜奇 温树杰[1,2] 刘浚基 景彬余 LIU Weiqi;WEN Shujie;LIU Junji;JING Binyu(College of Civil and Surveying Engineering, Jiangxi University of Science and Technology, Ganzhou, Jiangxi 341000, China;Jiangxi Provincial Key Laboratory of Environmental Geotechnical Engineering and Disaster Control, Jiangxi University of Science and Technology, Ganzhou, Jiangxi 341000, China)
机构地区:[1]江西理工大学土木与测绘工程学院,江西赣州341000 [2]江西理工大学江西省环境岩土与工程灾害控制重点实验室,江西赣州341000
出 处:《公路工程》2022年第3期76-81,共6页Highway Engineering
基 金:国家自然科学基金项目(51304084);江西省自然科学基金项目(20151BAB206026);“清江青年英才计划”优秀人才项目(JXUSTQJYX2016001)。
摘 要:对于一些安全系数较低的边坡,需对其进行加筋处理,然而目前常用的加筋边坡稳定性计算方法较为繁杂。为此,基于最小势能原理,针对土工格栅加筋边坡,引入格栅变形势能与摩擦势能概念构建系统势能函数,并求解滑体的虚位移d→,然后通过力与位移的关系得到滑裂面上的法向力和极限抗滑力,继而求得安全系数,最后通过算例与其他边坡稳定性分析方法计算结果对比验证该方法的合理性。结果表明:该方法是合理可行的;随着土工格栅长度或加筋层数的变化,其安全系数变化的趋势符合传统极限平衡法与工程实际情况。该方法无需划分条块,无需迭代,计算量小,便于在实际工程中使用。Some slopes with low safety factors need to be reinforced.However,the commonly used methods for calculating the stability of reinforced slopes are complicated.For this reason,based on the principle of minimum potential energy,this paper introduces the concepts of grid deformation potential energy and friction potential energy to construct the system potential energy function for geogrid-reinforced slopes,and calculates the virtual displacement of the sliding body.Then,the sliding body is obtained through the relationship between force and displacement.The normal force and the ultimate anti-sliding force on the crack surface are then obtained,and the safety factor is obtained.Finally,a calculation example is compared with the calculation results of other slope stability analysis methods to verify the rationality of the method.The results show that the method is reasonable and feasible;with the change of the length or number of layers of the geogrid the trend of the safety factor is in line with the traditional limit equilibrium method and the actual engineering situation.This method does not need to be divided into blocks,does not need to be iterated,has a small amount of calculation,and is convenient for use in actual projects.
分 类 号:U416.14[交通运输工程—道路与铁道工程]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.7