α+β型钛合金惯性摩擦焊接头焊态/热处理态组织特征及性能  

Microstructure Characteristics and Mechanical Properties of Inertia Friction Welding Joint of α+β Titanium Alloy in Welding State/Post-Weld Heat Treatment State

作　　者：乌彦全 周军 张春波 梁武 李睿 秦丰 Wu Yanquan;Zhou Jun;Zhang Chunbo;Liang Wu;Li Rui;Qin Feng(Harbin Welding Institute Limited Company,Harbin 150028,China;Heilongjiang Key Laboratory of Advanced Friction Welding Technology and Equipment,Harbin 150028,China)

机构地区：[1]哈尔滨焊接研究院有限公司,黑龙江哈尔滨150028 [2]黑龙江省先进摩擦焊接技术与装备重点实验室,黑龙江哈尔滨150028

出　　处：《稀有金属材料与工程》2022年第6期2144-2150,共7页Rare Metal Materials and Engineering

基　　金：黑龙江省省院科技合作项目(YS20A19);国家自然科学基金青年科学基金项目(52005139)。

摘　　要：采用SEM、EBSD及TEM等表征手段分析了惯性摩擦焊接头在焊态及焊后热处理态下的微观组织形貌与分布特征,并研究了焊后热处理态下的接头力学性能。结果表明,焊缝区为单一等轴α晶粒,在焊态下由板条状马氏体α′相+晶界片状α_(p)相+亚稳态β相构成,并伴随着(0001)//ND丝织构。热处理后转变为晶界片状α_(p)相+晶内片状α_(s)+β相,在原有丝织构的基础上形成了(2113)[2119]取向织构;焊缝区显微硬度最高,随着向母材区过渡显微硬度逐渐降低,焊后热处理可降低焊缝区硬度,使接头硬度分布较为均匀。接头在室温下的拉伸试验均断裂于远离焊缝中心的母材区。The microstructure morphology and distribution characteristics of inertial friction welded joint were analyzed in welding state and post-welding heat treatment state by SEM,EBSD and TEM.In addition,the mechanical properties of the joint in post-welding heat treatment state were studied.The results show that the weld zone is single equiaxed α grains,which is composed of lamellar martensite α'phase+grain boundary lamellar α_(p) phase+metastable β phase in welding state,and with(0001)//ND fiber texture.The microstructure is consisted of grain boundary lamellar α_(p) phase+intragranular lamellar α_(s)+β phase after post-weld heat treatment.The(2113)[2119]orientation texture is also formed on the basis of the original fiber texture.Under the effect of welding pressure and thermal cycling,the equiaxed α_(p) phase in thermo-mechanically affected zone has been transformed into a rod and approximately paralleled to the welding interface.The equiaxed α_(p) phase in thermal affected zone still maintains original shape.The weld zone has the highest microhardness,which gradually decreases from weld zone to base metal.The post-weld heat treatment can reduce the hardness of the weld zone and obtain uniform hardness distribution in welded joint.The tensile specimens at room temperature fail in the base metal away from weld center line.

关 键 词：钛合金 惯性摩擦焊 织构 微观组织 

分 类 号：TG456.9[金属学及工艺—焊接] TG146.23[一般工业技术—材料科学与工程]