汽车轮毂旋压成形工艺研究  

Spinning Forming Technology of Automobile Wheel Hub

作　　者：赵玉霞[1] 孙华雨[1] 方雷 ZHAO Yu-xia;SUN Hua-yu;FANG Lei(Henan Vocational College of Mechanical and Electrical Engineering,Henan Xinzheng 451191,China)

机构地区：[1]河南机电职业学院,河南新郑451191

出　　处：《精密成形工程》2022年第7期124-129,共6页Journal of Netshape Forming Engineering

摘　　要：目的 优化汽车轮毂旋压成形过程中的工艺参数。方法 设计了四因素四水平正交试验,研究了摩擦因数、旋轮圆角半径、进给率、主轴转速对第1道次和第2道次试样壁厚比值的影响。结果 在第1道次中,进给率对壁厚比值影响最大,其次是摩擦因数、旋轮圆角半径,主轴转速对壁厚比值影响较小。在第2道次中,摩擦因数对壁厚比值影响最大,其次是主轴转速,最后为旋轮圆角半径和进给率。结论 第1道次最优工艺组合为ABCD,即摩擦因数为0.4,旋轮圆角半径为25 mm,进给率为0.7 mm/r,主轴转速为150r/min;第2道次最优工艺组合为ABCD,即摩擦因数为0.2,旋轮圆角半径为8 mm,进给率为1.4 mm/r,主轴转速为210 r/min。所制备的轮毂在0°、90°、180°、270°等4个位置测得的屈服强度相近、抗拉强度也相近,屈服强度和抗拉强度的均值分别为213MPa和263MPa,说明所制备的轮毂在4个角度位置具有较优的力学性能均匀性。The work aims to optimize the technological parameters of automobile wheel hub during spinning forming.Four-factor and four-level orthogonal experiment was designed to study the effects of friction coefficient, wheel fillet radius,feed rate, and spindle speed on the wall thickness ratio of the first pass and the second pass. In the first pass, the feed rate range had the greatest effects on the wall thickness ratio, followed by the friction coefficient and the wheel fillet radius. The spindle speed range was the smallest, and had little effect on the wall thickness ratio. In the second pass, the friction coefficient had the greatest effects on the wall thickness ratio, followed by the spindle speed, and finally the wheel fillet radius and feed rate. The optimal process combination of the first pass is ABCD, that is, the friction coefficient is 0.4, the wheel fillet radius is 25 mm,the feed rate is 0.7 mm/r, and the spindle speed is 150 r/min. The optimal process combination of the second pass is ABCD,that is, the friction coefficient is 0.2, the wheel fillet radius is 8 mm, the feed rate is 1.4 mm/r, and the spindle speed is 210 r/min.The yield strength and tensile strength of the prepared hub measured at four positions of 0°, 90°, 180° and 270° are similar, respectively, and the mean values correspond to 213 MPa and 263 MPa, indicating that the prepared wheel hub has good mechanical performance uniformity at four positions.

关 键 词：旋压成形 汽车轮毂 壁厚比值 摩擦因数 旋轮圆角半径 进给率 主轴转速 

分 类 号：TG306[金属学及工艺—金属压力加工]