高速脂润滑滚动轴承密封结构优化与漏脂试验  

Sealing Structure Optimization and Grease-Leakage Test of High-speed Grease-lubricated Rolling Bearing

作　　者：张帅[1,2] 杜学芳 马纯 姜艳红 张文虎 邓四二 ZHANG Shuai;DU Xuefang;MA Chun;JIANG Yanhong;ZHANG Wenhu;DENG Sier(School of Mechatronics Engineering,Henan University of Science and Technology,Luoyang Henan 471003,China;School of Mechanical Engineering,Henan Institute of Technology,Xinxiang Henan 453003,China;Jiayouyi Bearing Technology Co.,Ltd.,Jiaxing Zhejiang 314011,China;Zhongzhe High-speed Railway Bearing Co.,Ltd.,Longyou Zhejiang 324400,China)

机构地区：[1]河南科技大学机电工程学院,河南洛阳471003 [2]河南工学院机械工程学院,河南新乡453003 [3]嘉优易轴承科技有限公司,浙江嘉兴314011 [4]中浙高铁轴承有限公司,浙江龙游324400

出　　处：《润滑与密封》2022年第9期111-117,共7页Lubrication Engineering

基　　金：国家国防科研项目(TDGC-JD-19-126-1);国家自然科学基金项目(51905152)。

摘　　要：针对高速脂润滑滚动轴承密封过早失效的问题,建立油封的热-应力耦合有限元模型,研究油封主要参数和轴承工况参数对油封唇口的最高温度和最大接触应力的影响规律,对油封结构参数进行优化,利用强化温升漏脂试验台进行试验验证。结果表明:高速脂润滑滚动轴承油封密封性能的研究应该考虑温度的影响;唇口的最高温度随轴向过盈量、橡胶材料硬度、密封面摩擦因数、轴承转速和轴承腔内温度的增大而增大;最大接触应力随轴向过盈量和橡胶材料硬度的增大而增大,随密封面摩擦因数、轴承转速和轴承腔内温度的增大变化不大;密封结构优化后,平均漏脂率下降了56.7%,平均温升下降了54.3%。Aiming at the early failure of oil seal in high-speed grease-lubricated rolling bearing,the thermal-stress coupled finite element model of oil seal was established,and the influence of main parameters of oil seal and working condition parameters of bearing on the maximum temperature and contact stress of oil seal lip were studied.The structural parameters of the oil seal were optimized and verified by the enhanced temperature-rise grease-leakage test bench.The results show that the influence of temperature should be considered in the study of oil sealing performance of high-speed grease-lubricated rolling bearing.The maximum temperature of seal lip increases with the increase of axial interference,hardness of rubber material,friction coefficient of sealing surface,bearing speed and temperature in bearing cavity.The maximum contact stress increases with the increase of the axial interference and the hardness of the rubber material,but changes little with the increase of the friction coefficient of the sealing surface,the bearing speed and the temperature in the bearing cavity.After the sealing structure optimization,the average grease leakage rate is reduced by 56.7%and the average temperature rise is reduced by 54.3%.

关 键 词：密封结构 滚动轴承 脂润滑 漏脂试验 热-应力耦合 

分 类 号：TH117.1[机械工程—机械设计及理论]