检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:周宇昊 阮炯明 洪国同[1,2] 苗政 ZHOU Yuhao;RUAN Jiongming;HONG Guotong;MIAO Zheng(Key Laboratory of Technology on Space Energy Conversion,Technical Institute of Physics and Chemistry,Chinese Academy of Science,Beijing 100190,China;University of Chinese Academy of Sciences,Beijing 100049,China;Huadian Electric Power Research Institute Co.,Ltd.,Hangzhou 310030,China;Beijing Key Laboratory of Multi-phase Flow and Heat Transfer of Low-grade Energy(North China Electric Power University),Beijing 102206,China)
机构地区:[1]中国科学院理化技术研究所,中国科学院空间工热转换技术重点实验室,北京100190 [2]中国科学院大学,北京100049 [3]华电电力科学研究院有限公司,浙江杭州310030 [4]低品位能源多相流与传热北京市重点实验室(华北电力大学),北京102206
出 处:《热力发电》2022年第9期148-154,共7页Thermal Power Generation
基 金:国家自然科学基金项目(51776064)。
摘 要:针对分布式能源系统中可利用热源的温度和流量频繁波动的特点,测试了kW级有机朗肯循环原型机组在110~150℃波动热源下的运行性能和以工质流量与膨胀机转速为控制变量的多工况运行能力。结果表明,通过调节工质流量可以在相对平稳的热效率下实现对机组输出功率的有效控制。机组输出功率随热源温度变化剧烈,但随热源流量变化规律不一:小工质流量下,换热面积冗余较多,热源流量的变化对机组性能的影响可以忽略;随着工质流量的提高,热源流量的影响逐渐凸显,表现为机组性能随工质流量下降而明显降低。机组在热源温度150℃下获得最大输出功约4 kW,最大热效率6.0%。In view of the frequent fluctuation of temperature and flow rate of the available heat source in distributed energy system,the performance of the kW-scale organic Rankine cycle prototype with fluctuating heat source of 110~150 ℃ was tested and its multi-condition operation characteristics with the working fluid flow rate and expander rotary speed as the control variables was analyzed.The results showed that,the fluid mass flow rate was an effective control parameter to adjust the shaft power while maintaining the relatively stable system thermal efficiency.The shaft power was sensitive to the variation of heat source temperature while it exhibited different trends with the heat source mass flow rate.When the fluid mass flow rate was relatively small,there was enough redundancy in the heat transfer area.Under this condition,the heat source flow rate had quite weak effect on the ORC performance.With an increase in the fluid flow rate,the effect of heat source flow rate emerged.The ORC performance was deteriorated with the reducing heat source flow rate.The maximum shaft power and thermal efficiency of 4 kW and 6.0% could be achieved at the heat source temperature of 150 ℃.
分 类 号:TK123[动力工程及工程热物理—工程热物理] TM611[动力工程及工程热物理—热能工程]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.222