检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:张天雄[1] 王元清[2] 陈志华[1] 卜宜都 何伟[4] 衡月昆[4] ZHANG Tianxiong;WANG Yuanqing;CHEN Zhihua;BU Yidu;HE Wei;HENG Yuekun(School of Civil Engineering,Tianjin University,Tianjin 300072,China;Key Laboratory of Civil Engineering Safety and Durability of Ministry of Education,Tsinghua University,Beijing 100084,China;Department of Civil Engineering,Beijing University of Technology,Beijing 100124,China;Institute of High Energy Physics,Chinese Academy of Sciences,Beijing 100049,China)
机构地区:[1]天津大学建筑工程学院,天津300072 [2]清华大学土木工程安全与耐久教育部重点实验室,北京100084 [3]北京工业大学土木工程系,北京100124 [4]中国科学院高能物理研究所,北京100049
出 处:《工业建筑》2022年第7期98-105,97,共9页Industrial Construction
基 金:国家自然科学基金(国家重大科研仪器研制项目12127808);清华大学自主科研计划课题(学科交叉专项20131089288)。
摘 要:目前,国内外有关不锈钢高强度螺栓的研究较少,且螺栓产品规格缺乏统一标准。为研究不锈钢高强度螺栓的机械性能与施拧方法,对两种新型10.9级不锈钢高强度螺栓开展了实物拉伸试验、硬度试验及紧固性能试验,获得了螺栓的抗拉强度、硬度等重要指标,确定了不锈钢高强度螺栓的预紧力与施拧工艺。结果表明:两种不锈钢高强度螺栓均满足10.9级高强度螺栓机械性能的要求;不锈钢螺栓在紧固过程中会发生咬死现象,润滑剂Molykote D-321R对不锈钢螺栓咬死的减摩润滑效果最好,可使不锈钢高强度螺栓的扭矩系数降低至钢结构用高强度螺栓扭矩系数的限值;对于扭矩法与转角法两种施加螺栓预紧力的方法,扭矩法得到的螺栓预紧力一致性更高;并提出了不锈钢高强度螺栓施工预紧力的要求,进而给出了其施工扭矩,为工程应用提供参考。There are few researches on stainless steel high strength bolts worldwide,and there is a lack of uniform standards for bolt product specifications.In order to study the mechanical properties and tightening methods of stainless steel high strength bolts,physical tensile tests,hardness tests and tightening tests were carried out on two kinds of 10.9 grade stainless steel high-strength bolts.The tensile strength and hardness were obtained.The preload and tightening process were determined.The results showed that the two kinds of stainless steel high-strength bolts met the requirements of mechanical properties of grade 10.9 high-strength bolts.The thread galling of stainless steel bolts occurred during the tightening process.The lubricant Molykote D-321 R had the best friction reduction effect on the galling and could reduce the torque coefficient of stainless steel high-strength bolts to the limit of torque coefficients of the high-strength bolts for steel structures.For the two methods of applying bolt preload,the torque method and the rotation angle method,the bolt preload obtained by the torque method was more consistent.The requirements for the construction preload of stainless steel high-strength bolts were proposed,and the construction torque was given to provide a reference for engineering application.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.15