检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:齐国宁 米江 王峥嵘[2] QI Guoning;MI Jiang;WANG Zhengrong(AVIC Xi'an Aero-engine Controls Technology Co.,Ltd.,Xi'an Shaanxi 700077,China;College of Energy and Power Engineering,Lanzhou University of Technology,Lanzhou Gansu 730050,China)
机构地区:[1]中国航发西安动力控制科技有限公司,陕西西安700077 [2]兰州理工大学能源与动力工程学院,甘肃兰州730050
出 处:《机床与液压》2022年第20期38-41,共4页Machine Tool & Hydraulics
摘 要:为减小配流冲击,高压柱塞泵的柱塞腔在过渡过程中必须通过机械闭死压缩、膨胀和减振槽引油共同作用来实现预升压和预卸压。此过程中,减振槽的两端均作用较大变化的压差,槽中的油液产生较大速度的压差流,导致出现低压区,形成气穴,气泡破裂时产生气蚀,破坏配流盘和缸体表面,大幅降低泵的容积效率。进行耐久性试验,研究配流气蚀破坏的特征和容积效率的变化。结果表明:在现有配流结构下,配流气蚀严重,耐久性试验仅开展了600 h,缸体表面已出现严重的气蚀破坏,导致泵的容积效率大幅下降。为提高泵的耐久性和提高容积效率,必须研究抗气蚀配流结构以减小配流副表面的配流气蚀破坏。In order to reduce the impact of flow distribution,the piston cavity of high-pressure piston pump must realize pre-pressure rise and pre-pressure release through the joint action of mechanical closed compression,expansion and oil introduction of damping groove in the transition process.In this process,the two ends of the damping groove are acted on a large varying differential pressure,and the oil in the groove produces a high-speed differential pressure flow,the low-pressure areas are generated,the cavitation is formed,and the cavitation is occured when the bubble is broken,the surfaces of the valve plate and cylinder block are destroyed,and the volume efficiency of the pump is greatly reduced.The durability test was conducted,the characteristics of distribution cavitation damage and the change of volumetric efficiency were studied.The results show that under the existing distribution structure,the distribution cavitation is serious,durability test only carries out 600 h,the surface of the cylinder has appeares serious gas erosion damage,the pump volume efficiency droppes significantly.To improve the pump durability and volume efficiency,gas corrosion resistance structure must be studied to reduce the current gas erosion damage of the current subsurface.
分 类 号:TH137.51[机械工程—机械制造及自动化]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:3.17.81.34