检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:毕然[1] 吴金国[1] 贾连光[1] 潘代琦 王春刚[1] BI Ran;WU Jinguo;JIA Lianguang;PAN Daiqi;WANG Chungang(School of Civil Engineering,Shenyang Jianzhu University,Shenyang,China,110168;The Fourth Construction Engineering Co.Ltd.,China Construction Second Engineering Bureall,Tianjin,China,300457)
机构地区:[1]沈阳建筑大学土木工程学院,辽宁沈阳110168 [2]中建二局第四建筑工程有限公司,天津300457
出 处:《沈阳建筑大学学报(自然科学版)》2022年第5期786-794,共9页Journal of Shenyang Jianzhu University:Natural Science
基 金:国家自然科学基金项目(51977422)。
摘 要:目的 研究不同等级高强螺栓的拉力和撬力分布规律以及对蜂窝梁-柱端板连接节点的破坏形式和滞回性能的影响,为后续研究提供参考。方法 应用ABAQUS建立数值模型,在与试验结果吻合的基础上,分析螺栓等级、直径、预紧力和端板厚度等参数对蜂窝梁-柱端板连接节点性能的影响。结果 蜂窝梁可以起到转移塑性铰的作用,减小连接处端板变形;端板-梁翼腹板双铰耗能破坏的节点延性和耗能性能更好;端板厚度相同时,螺栓直径和预紧力对节点极限承载力的影响较小;撬力随螺栓直径和预紧力的增加而减小,随端板厚度增加而增大。结论 端板厚度增加有利于蜂窝孔的应力迁移作用,使节点发生端板-梁翼腹板双塑性铰耗能破坏,但撬力影响不可忽略;随螺栓直径和预紧力的增大,选用较厚端板的节点破坏模式由端板强铰向梁强铰转化。This paper was proposed to study the failure mode,hysteretic performance,bolt tension and pry force of castellated beam-to-column end plate connections affected by high-strength bolts,and to provide reference for subsequent research.A numerical model was established by using ABAQUS,and the effects of bolt grade,diameter,preload and end plate thickness on the performance of castellated beam-to-column end plate connections were analyzed based on the results of test.The castellated beam can transfer the plastic hinge and reduce the deformation of the end plate.The ductility and energy dissipation performance of end plate-beam-wing web joints are better.When the end plate thickness is the same,the bolt diameter and preload have little influence on the ultimate bearing capacity of the connections.The prying force decreases with the increase of bolt diameter and preload,and increases with the increase of end plate thickness.The increase of the end plate thickness is beneficial to the stress migration of the opening,which causes the energy dissipation failure of the end plate-beam-wing web double plastic hinge at the joint point,but the influence of the prying force cannot be ignored.With the increase of bolt diameter and preload,the failure mode of joints with thicker end plates is transformed from strong hinge of end plate to strong hinge of beam.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.49