热处理对大变形量Zn-1.65Cu-0.15Ti合金的组织和性能的影响  被引量:2

Effect of Heat Treatment on Microstructure and Properties of Zn-1.65Cu-0.15Ti with Large Deformation

在线阅读下载全文

作  者:徐英卓 王秀凯 常麟晖 陈步明[1,2,3] 黄惠 何亚鹏[1,2,3] 郭忠诚 XU Yingzhuo;WANG Xiukai;CHANG Linhui;CHEN Buming;HUANG Hui;HE Yapeng;GUO Zhongcheng(Faculty of Metallurgical and Energy Engineering,Kunming University of Science and Technology,Kunming 650093,China;Research Center of Metallurgical Electrode Materials Engineering Technology of Yunnan Province,Kunming 650106,China;Kunming Hendera Science and Technology Co.,Ltd.,Kunming 650106,China)

机构地区:[1]昆明理工大学冶金与能源工程学院,昆明650093 [2]云南省冶金电极材料工程技术研究中心,昆明650106 [3]昆明理工恒达科技股份有限公司,昆明650106

出  处:《材料导报》2022年第23期110-116,共7页Materials Reports

基  金:国家自然科学基金(51504111,51564029);中国博士后科学基金(2018M623418);云南省科技创新人才工程项目(2019HB111)。

摘  要:本实验采用中频感应熔炼炉制备锌铜钛合金,通过热轧工艺制备了变形Zn-Cu-Ti合金。首先分析了合金的显微组织和拉伸性能随着变形量的变化,发现随着变形量的增加金相组织变得越来越不明显,轧制的方向越来越清晰。96.7%变形量的合金延伸率最高,可达到54.7%。通过电化学分析发现,合金变形量越大,合金板材的耐蚀性越好。接着进一步研究了不同的热处理温度和时间对合金力学性能以及微观组织的影响。合金在210℃经过热处理,硬度从46HV提高至73HV,在温度稍低时,150~180℃区间内硬度增大的趋势更明显。高温热处理有利于合金抗拉强度的提高,在240℃下热处理保温2 h,抗拉强度和延伸率分别提高约29%、20%。In this work,the medium frequency induction melting furnace was used to prepare a zinc-copper-titanium alloy,and deformed Zn-Cu-Ti alloy was prepared by a hot rolling process.Firstly,the changes of microstructure and tensile properties of alloys with deformation were analyzed.With the increase of deformation,the microstructure becomes less and less obvious,while the direction of rolling becomes more and more clear.The elongation of 96.7%alloy is the highest and can reach 54.7%.Through electrochemical analysis,it is found that the greater the deformation of the alloy,the better the corrosion resistance of the alloy sheet.In addition,the effects of different heat treatment temperature and annealing time on the mechanical properties and electrochemical properties of the alloy were also studied.After heat treatment at 210℃,the hardness of the alloy increases from 46 HV to 73 HV,and the hardness increasing trend is more obvious under heat treatment at 150—180℃.High temperature heat treatment is conducive to improve the tensile strength of the alloy.With heat treatment at 240℃for 2 h,the tensile strength and elongation increase 29%and 20%respectively.

关 键 词:锌铜钛合金 力学性能 热处理 微观结构 电化学性能 

分 类 号:TU512.2[建筑科学—建筑技术科学]

 

参考文献:

正在载入数据...

 

二级参考文献:

正在载入数据...

 

耦合文献:

正在载入数据...

 

引证文献:

正在载入数据...

 

二级引证文献:

正在载入数据...

 

同被引文献:

正在载入数据...

 

相关期刊文献:

正在载入数据...

相关的主题
相关的作者对象
相关的机构对象