AgCuTi活性钎料的轧制加工和性能研究  

Study on rolling process and properties of AgCuTi active solder

作　　者：刘国化 赵君[1] 王剑平[1] 张乃千 魏明霞 赵通明 金国成 周丕云 LIU Guo-hua;ZHAO Jun;WANG Jian-ping;ZHANG Nai-qian;WEI Ming-xia;ZHAO Tong-ming;JIN Guo-cheng;ZHOU Pi-yun(Kunming Institute of Precious Metals,State Key Laboratory of Advanced Technologies for Comprehensive Utilization of Platinum Metal,Sino-Platinum metals Co.Ltd,Kunming,650106,China;AECC Shenyang Liming Aero-engine Co.Ltd.,Shenyang 110043,China)

机构地区：[1]昆明贵金属研究所,贵研铂业股份有限公司稀贵金属综合利用新技术国家重点实验室,昆明650106 [2]中国航发沈阳黎明航空发动机有限责任公司,沈阳110043

出　　处：《贵金属》2022年第S01期22-28,共7页Precious Metals

基　　金：国家科技部“科技助力经济2020”重点专项;云南省稀贵金属材料基因工程(202002AB080001-1);云南省2019材料基因工程项目(2019ZE001-2);云南省科技人才与平台计划(202105AE160027)。

摘　　要：采用粉末冶金的方法,制备了两种成分的AgCuTi活性钎料。用金相显微镜、扫描电子显微镜(SEM)、能谱分析(EDS)、X射线衍射(XRD)等研究了合金片材的组织形貌与结构。探讨了在不同的轧制变形量下,两种合金的变形量与组织结构、硬度、密度、电导率等物理、力学、电学性能的关系,分析了轧制撕裂断口的形貌和类型。结果表明,Ag-27.5Cu-2.5Ti和Ag-28Cu-4Ti两种成分活性钎料的组织结构、性能、断裂机理不一样,Ag-28Cu-4Ti的铜钛相分布较多、硬度较高、密度较低、电导率较小,同时塑性较差,轧制撕裂过程脆性断裂占主要部分;Ag-27.5Cu-2.5Ti塑性较好,轧制撕裂过程塑性断裂占主要部分。AgCuTi active solders with two components were prepared by powder metallurgy.The microstructure and structure of AgCuTi alloy sheet were studied by means of metallographic microscope,SEM,EDS and XRD.The relationship between the deformation of the two alloys and the physical,mechanical and electrical properties such as microstructure,hardness,density and conductivity under different rolling deformation were discussed.The morphology and types of rolling tear fracture are analyzed.The results show that the microstructure,properties and fracture mechanism of Ag-27.5Cu-2.5Ti and Ag-28Cu-4Ti active solders are different.Ag-28Cu-4Ti has more Cu-Ti phase distribution,higher hardness,lower density,lower conductivity and poor plasticity,brittle tearing accounts for the main part in the rolling tearing process;Ag-27.5Cu-2.5Ti has better plasticity,and rolling tear plastic tear is the main part.

关 键 词：金属材料 AgCuTi 活性钎料 轧制 

分 类 号：TG146.3[一般工业技术—材料科学与工程]