基于正多边形截面薄壁零件旋压成形质量研究  

Research on spinning quality of thin-walled parts based on regular polygon section

作　　者：王佰超 张欣龙 高建军 张澧桐 张洪明 王慧冬 WANG Baichao;ZHANG Xinlong;GAO Jianjun;ZHANG Litong;ZHANG Hongming;WANG Huidong(School of Mechanical Engineering,Changchun University of Science and Technology,Changchun 130022,CHN;Inner Mongolia First Machinery Group Co.,Ltd.,Baotou 014000,CHN)

机构地区：[1]长春理工大学机电工程学院,吉林长春130022 [2]内蒙古第一机械集团股份有限公司,内蒙古包头014000

出　　处：《制造技术与机床》2023年第1期132-138,共7页Manufacturing Technology & Machine Tool

摘　　要：基于新型非圆旋压成形方法,讨论正多边形零件旋压成形的旋轮对零件轮廓的成形轨迹方程。以等边三角形截面以及正五边形截面的旋压为例,研究新型非圆旋压成形方法在旋压过程中的主轴转速、旋轮进给比和道次三项工艺参数对正多边形截面旋压件壁厚差的影响。应用有限元软件进行仿真分析,根据仿真结果分析正多边形旋压件的壁厚分布规律,即正多边形旋压件的壁厚呈周期性分布,最大壁厚发生在正多边形旋压件的圆角处。采用Box-Behnken实验设计方法设计仿真实验,根据仿真数据对零件的壁厚差进行方差分析,建立了关于壁厚差的预测模型并对其进行优化,最后进行多组仿真研究用来验证模型准确性。结果表明主轴转速、旋轮进给比、道次对正多边形零件壁厚差的影响显著,主轴转速与壁厚差呈正相关,而进给比壁厚差呈负相关,道次对壁厚差的影响先减小后增加。Based on the new non-circular spinning forming method, the forming trajectory equation of the contour of the spinning wheel pair of polygonal parts was discussed. Taking the spinning of equilateral triangle section and regular pentagonal section as an example, the influence of three technological parameters,namely, spindle speed, feed ratio of spinning wheel and passes, on the wall thickness difference of spinning parts with regular polygon section in the spinning process of the new non-circular spinning forming method was studied. The finite element software is used for simulation analysis. According to the simulation results, the wall thickness distribution of the regular polygon spinning parts was analyzed, that is, the wall thickness of the regular polygon spinning parts was distributed periodically,and the maximum wall thickness occurs to the corner of the regular polygon spinning parts. The Box-Behnken experimental design method was used to design the simulation experiment. The variance analysis of the wall thickness difference between in the parts was carried out according to the simulation data, and the prediction model of the wall thickness difference was established and optimized. Finally, multiple groups of simulation study are carried out to verify the accuracy of the model. The results show that the spindle speed, the feed ratio of the spinning wheel and the pass have significant effects on the wall thickness difference of the regular polygon parts. The spindle speed was positively related to the wall thickness difference, while the feed ratio was negatively related to the wall thickness difference. The effect of the pass on the wall thickness difference decreases first and then increases.

关 键 词：非圆旋压 旋压成形方法 工艺参数 壁厚差 响应曲面 

分 类 号：TG306[金属学及工艺—金属压力加工]