连续碳纤维增强复合材料3D打印喷头设计与实验分析  

Design and experimental analysis of 3D printing nozzle for continuous carbon fiber reinforced composites

作　　者：刘基盛 王叶松 李威[1] 贾志新[1] 方鹏程 LIU Jisheng;WANG Yesong;LI Wei;JIA Zhixin;FANG Pengcheng(School of Mechanical Engineering,University of Science and Technology Beijing,Beijing 100083,CHN;School of Mechanical,Jiangsu University of Science and Technology Engineering,Zhenjiang 212000,CHN;Department of Industrial Engineering,Tsinghua University,Beijing 100084,CHN)

机构地区：[1]北京科技大学机械工程学院,北京100083 [2]江苏科技大学机械工程学院,江苏镇江212000 [3]清华大学工业工程系,北京100084

出　　处：《制造技术与机床》2023年第4期56-63,共8页Manufacturing Technology & Machine Tool

基　　金：国家自然科学基金(51775036)。

摘　　要：以“独立挤出”型连续碳纤维增强PLA复合材料(continuous carbon fiber reinforced PLA composite,CCFRC/PLA)3D打印制件为研究对象,设计了柔性的连续碳纤维增强PLA复合材料丝(continuous carbon fiber reinforced composite filament/PLA,CCFRCF/PLA)送丝机构,研究了打印喷嘴直径与CCFRCF/PLA直径、表面包裹树脂膨胀特性及打印层高的关系,探讨了喷嘴端面直径对打印表面热辐射的影响规律,推导了喷嘴直径的计算公式,求解了最佳喷嘴直径和最佳端面直径。基于设计的打印喷头,采用仿真分析与实验验证的方法,探索了打印层高与制件力学性能之间的关系,结果表明CCFRC/PLA的抗拉强度与纤维层数呈正相关,并验证了层合板预测模型的有效性,获得了打印层高0.1 mm时CCFRC/PLA抗拉强度的修正系数为0.039,打印层高0.2 mm时,修正系数为0.124,为连续碳纤维增强复合材料3D打印技术的发展提供了理论基础和参考价值。Taking the 3D printing products of continuous carbon fiber reinforced PLA composite(CCFRC/PLA)as the research object,a flexible wire feeding mechanism of continuous carbon fiber reinforced PLA composite(CCFRCF/PLA)was designed The relationship between the expansion characteristics of the resin coating on the surface and the height of the printing layer is discussed.The influence of the nozzle end diameter on the thermal radiation of the printing surface is discussed.The calculation formula of the nozzle diameter is derived,and the optimal nozzle diameter and the optimal end diameter are solved.Based on the designed print nozzle,the relationship between the print layer height and the mechanical properties of the fabricated part was explored by using experimental verification and simulation analysis,and the results showed that the tensile strength of CCFRC/PLA was positively correlated with the number of fiber layers,which verified the validity of the laminate prediction model.And the correction coefficient of the tensile strength of CCFRC/PLA is 0.039 for printing layer height of 0.1 mm and 0.124 for printing layer height of 0.2 mm,which provides a theoretical basis and reference value for the development of continuous carbon fiber reinforced composite 3D printing technology.

关 键 词：3D打印 独立挤出 连续碳纤维增强PLA复合材料 喷头设计 力学性能分析 

分 类 号：TH122[机械工程—机械设计及理论]