检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:肖代红[1] 孙伯儒 吴名冬 黄兰萍[1] 刘文胜[1] Xiao Daihong;Sun Boru;Wu Mingdong;Huang Lanping;Liu Wensheng(Science and Technology on High-strength Structural Materials,Central South University)
机构地区:[1]中南大学轻质高强结构材料重点实验室
出 处:《特种铸造及有色合金》2023年第5期583-589,共7页Special Casting & Nonferrous Alloys
基 金:轻质高强结构材料重点实验室基金资助项目(202005);中南大学大型仪器开放共享基金资助项目(202230)。
摘 要:采用真空熔炼铸造及热挤压方法制备了Al-3Li-0.1Zr-0.1Sc-xMn(x=0,1.2,5,质量分数,%)合金。通过金相显微镜、扫描电镜、拉伸性能、维氏硬度、纳米压痕等测试方法,研究了Mn的添加对合金强度、弹性模量及显微组织的影响。结果表明,Mn的添加缩短了合金的时效硬化过程,提高了合金硬度,促进合金中δ′-Al3Li相的时效析出。Mn含量为1.2%时,Al-3Li-0.1Zr-0.1Sc-1.2Mn合金的抗拉强度达到536 MPa,弹性模量达到82.7 GPa,比模量达到32.4 GPa·cm3/g。此外,讨论了固溶体及第二相与合金弹性模量的关系。Al-3Li-0.1Zr-0.1Sc-xMn(x=0,1.2,5,%)alloys were prepared by vacuum melting and hot extrusion.The effects of Mn addition on microstructure and properties of the alloys were investigated by optical microscope,scanning electron microscope,tensile test,Vickers hardness and nano-indentation.The results indicate that Mn addition can significantly shorten the aging hardening process and increase the hardness of alloy,promoting the aging precipitation ofδ′-Al_3Li phase.When the content of Mn is 1.2%,the tensile strength,modulus and specific modulus of Al-3Li-0.1Zr-0.1Sc-1.2Mn alloy reach 536 MPa,82.67 GPa and 32.42 GPa·cm~3/g,respectively.Moreover,the relationship between elastic modulus and solid solution or second phase were discussed.
关 键 词:AL-LI合金 MN元素 时效析出 弹性模量 力学性能
分 类 号:TG146.21[一般工业技术—材料科学与工程]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.179