检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:魏新园 王杲 周京欢 潘巧生 钱牧云 Wei Xinyuan;Wang Gao;Zhou Jinghuan;Pan Qiaosheng;Qian Muyun(School of Electrical and Information Engineering,Anhui University of Technology,Ma'anshan 243032,China;School of Instrument Science and Opto-Electronics Engineering,Hefei University of Technology,Hefei 230009,China)
机构地区:[1]安徽工业大学电气与信息工程学院,马鞍山243032 [2]合肥工业大学仪器科学与光电工程学院,合肥230009
出 处:《仪器仪表学报》2023年第7期44-52,共9页Chinese Journal of Scientific Instrument
基 金:安徽省重点研究与开发计划项目(2022f04020005);安徽省高等学校科研研究重点项目(2022AH050313)资助。
摘 要:机床热误差预测模型在不同工况下难以保持高预测精度是导致热误差实际补偿效果差的重要原因,对此本文提出一种基于迁移学习的异工况下机床热误差建模方法。首先利用核均值匹配算法获取不同工况下机床温度数据间的迁移权重,从而提出基于迁移学习的热误差建模方法;对不同工况下热误差数据进行差异显著性检验,并利用本文所提方法建立热误差预测模型,分析建模效果;然后比对分析本文所提建模方法与常用建模方法的实际预测效果,最后进行补偿验证实验以证明本文所提方法的有效性。结果表明,本文所提基于迁移学习的建模方法能够有效提升建模效果,其中迁移学习结合LASSO算法针对不同工况下热误差数据的预测精度和稳健性分别达到3.73和1.14μm,补偿后机床X/Y/Z 3个方向热误差分别保持在-2.3~3.1μm、-3.4~3.9μm和-3.3~4.6μm范围内。The difficulty in maintaining high prediction accuracy of machine tool thermal error prediction models under different working conditions is an important reason for thermal errors′poor actual compensation effect.This article proposes a modeling method for the thermal error of machine tools under different working conditions based on transfer learning.Firstly,the kernel mean matching algorithm is used to obtain the transfer weight between machine tool temperature data under different working conditions.And a thermal error modeling method based on transfer learning is proposed.Furthermore,the significance of differences in thermal error data under different working conditions is tested,and a thermal error prediction model is formulated by using the proposed method to analyze the modeling effect.Then,the actual prediction performance of the proposed modeling method and commonly used modeling methods are compared and analyzed.Finally,the compensation validation experiments are conducted to evaluate the effectiveness of the proposed method.The results show that the modeling method based on transfer learning proposed in this paper can effectively improve the modeling effect.The prediction accuracy and robustness of transfer learning combined with the LASSO algorithm under different working conditions reach 3.73 and 1.14μm,respectively.After compensation,the thermal errors in the X/Y/Z directions of the machine tool remain within-2.3~3.1μm,-3.4~3.9μm,and-3.3~4.6μm,respectively.
关 键 词:机床热误差 迁移学习 建模与补偿 异工况 预测效果
分 类 号:TH161[机械工程—机械制造及自动化] TG659[金属学及工艺—金属切削加工及机床]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:3.143.5.121