检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:张兆祥 张仲平 郑万刚 殷方好 佟彤 ZHANG Zhaoxiang;ZHANG Zhongping;ZHENG Wangang;YIN Fanghao;TONG Tong(Research Institute of Petroleum Engineering,SINOPEC Shengli Oilfield Company,Dongying City,Shandong Province,257000,China;Shandong Provincial Key Laboratory of Exploitation Technology for Heavy Oil Reservoir,Dongying City,Shandong Province,257000,China)
机构地区:[1]中国石化胜利油田分公司石油工程技术研究院,山东东营257000 [2]山东省稠油开采技术重点实验室,山东东营257000
出 处:《油气地质与采收率》2024年第1期103-110,共8页Petroleum Geology and Recovery Efficiency
基 金:国家自然科学基金企业创新发展联合基金“难采稠油多元热复合高效开发机理与关键技术基础研究”(U20B6003)。
摘 要:针对浅薄层特超稠油油藏蒸汽吞吐开发初期面临的油层厚度薄、原油黏度高、蒸汽热损失大、吞吐有效期短等问题,提出了冷热交替大周期吞吐开发模式,有效改善开发效果。为此开展了浅薄层特超稠油油藏冷热交替开采三维物理模拟研究,结果表明:受顶底盖层热损失影响,蒸汽吞吐温度下降迅速,峰值产量较高,但单周期生产时间较短,约100 min;降黏吞吐可以降低吞吐井附近含油饱和度,提高产油速度,降低含水率,延长吞吐周期50 min以上;提高温度可以增强降黏剂的降黏效果,第二周期开始冷热交替改善效果优于第一周期,其生产时间延长60 min,含水率降低45%,周期采出程度提高1.7%。利用数值模拟方法优化了冷热交替的注入参数,建立了该技术的政策界限:最佳转冷热交替的时机为2~3周期,注入强度为0.02 t/m;适用的油层厚度小于8 m,原油黏度小于200000 mPa•s,含油饱和度大于0.6,渗透率大于1000 mD。Small reservoir thickness,high crude oil viscosity,large steam heat loss,and short cyclic steam stimulation(CSS)pe-riod are problems facing in shallow-thin ultra-heavy oil reservoirs at the early stage of CSS development.Therefore,the develop-ment model of large CSS of alternating hot and cold fluid injection was proposed to improve the development effect effectively.In addition,carried out a three-dimensional physical simulation experiment of alternating heat and cold fluid injection in shallow-thin ultra-heavy oil reservoirs.The results show that the temperature of CSS decreases rapidly and the peak production is high because of the heat loss of the top and bottom cap rocks,but the single cycle production time is short,about 100 min.The injection of viscosity reducer can reduce the oil saturation near the well,improve the oil production rate,lower the water content,and increase the CSS period by more than 50 min at the production stage.Increasing temperature can enhance the viscosity reduction effect of the viscos-ity reducer,and the improvement effect during the second cycle is better than that during the first cycle.In addition,the production time is increased by 60 min,water content is cut by 45%,and the oil recovery is enhanced by 1.7%.The injection parameters of heat and cold fluid were optimized and the policy limits of this technology were established by a numerical simulation method:The best timing of alternating heat and cold fluid injection is the second or third cycle;and the injection strength is 0.02 t/m.The suitable reservoir thickness is less than 8 m;the crude oil viscosity is less than 200000 mPa·s;the oil saturation is higher than 0.6,and the permeability is higher than 1000 mD.
分 类 号:TE357.46[石油与天然气工程—油气田开发工程]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.66