国产BE100和国外Wikus硬质合金带锯条背材的性能对比分析  

Comparative analysis of performance of domestic BE100 and foreign Wikus carbide band saw blade backing materials

作　　者：黎豪杰 赵玉萍[4] 储爱民 吴海江 邹利华[1,2] 陈友明 董泽熙[3] 李滔 LI Hao-jie;ZHAO Yu-ping;CHU Ai-min;WU Hai-jiang;ZOU Li-hua;CHEN You-ming;DONG Ze-xi;LI Tao(School of Mechanical and Energy Engineering,Shaoyang University,Shaoyang 422000,China;Key Laboratory of Hunan Province for Efficient Power System and Intelligent Manufacturing,Shaoyang University,Shaoyang 422000,China;School of Materials Science and Engineering,Hunan University of Science and Technology,Xiangtan 411201,China;School of Civil and Engineering,Hunan University of Science and Technology,Xiangtan 411201,China)

机构地区：[1]邵阳学院机械与能源工程学院,湖南邵阳422000 [2]邵阳学院高效动力系统智能制造湖南省重点实验室,湖南邵阳422000 [3]湖南科技大学材料科学与工程学院,湖南湘潭411201 [4]湖南科技大学土木工程学院,湖南湘潭411201

出　　处：《材料热处理学报》2024年第2期148-155,共8页Transactions of Materials and Heat Treatment

基　　金：国家自然科学基金(52174344);湖南省自然科学基金(2021JJ30249,2021JJ30250,2023JJ30222);湖南省大学生创业训练项目(S202210534024X);邵阳学院研究生科研创新项目(CX2023SY074)。

摘　　要：以国产BE100和国外Wikus两种硬质合金带锯条背材为研究对象,采用光学显微镜、扫描电镜(SEM)、X射线衍射仪(XRD)和维氏硬度计等研究了背材的微观组织、物相及硬度,使用拉伸试验机和疲劳试验机测试其拉伸性能和疲劳性能,对比研究了两种背材的微观组织和力学性能。结果表明:两种背材的主要成分Fe、Cr和Ni均以单相固溶体存在,且背材中形成的碳化物均为非晶态;相比BE100背材,Wikus背材采用高温淬火和低温回火的热处理工艺,产生了马氏体固溶强化效果,获得了更高的硬度;BE100和Wikus背材的微观组织分别由回火索氏体和回火屈氏体组成,Wikus背材微观组织的均匀性更好;拉伸初始时BE100背材的塑性优于Wikus背材,但随应变量增至10%则低于Wikus背材,BE100背材比Wikus背材更早出现颈缩现象;此外,Wikus背材比BE100背材具有更好的疲劳稳定性。Microstructure,phase and hardness of the domestic BE100 and foreign Wikus carbide band saw blade backing materials were studied by means of optical microscope,scanning electron microscopy(SEM),X-ray diffraction(XRD) and Vickers hardness tester,the tensile properties and fatigue properties of the two backing materials were tested using tensile testing machines and fatigue testing machines,and microstructure and mechanical properties of the two backing materials were compared and studied.The results show that the main components Fe,Cr and Ni in the two backing materials exist as single-phase solid solutions,and the carbides formed in the backing materials are all amorphous.Compared to the BE100 backing material,the Wikus backing material adopts a heat treatment process of high-temperature quenching and low-temperature tempering,resulting in martensitic solid solution strengthening effect and higher hardness.The microstructure of the BE100 and Wikus backing materials is composed of tempered sorbite and tempered troostite,respectively,and the uniformity of the microstructure of the Wikus backing materials is better.At the initial stage of tensile,the plasticity of the BE100 backing material is better than that of the Wikus backing material,but as the strain increases to 10%,it is lower than the Wikus backing material.The necking phenomenon of the BE100 backing material appears earlier than the Wikus backing material.In addition,the Wikus backing material has better fatigue stability than the BE100 backing material.

关 键 词：硬质合金带锯条 背材 微观组织 力学性能 热处理工艺 

分 类 号：TG142.4[一般工业技术—材料科学与工程]