光固化环氧丙烯酸酯体系优化与性能研究  

Optimization of UV-curable epoxy acrylate system and its properties

作　　者：崔靖晖 赵秋丽[1] 杨庆浩[1] Cui Jinghui;Zhao Qiuli;Yang Qinghao(College of Materials Science and Engineering,Xian University of Science and Technology,Xi'an 710054)

机构地区：[1]西安科技大学材料科学与工程学院,西安710054

出　　处：《化工新型材料》2024年第3期177-180,186,共5页New Chemical Materials

基　　金：国家自然科学基金(U1766218)。

摘　　要：以己二醇二丙烯酸酯和三丙二醇二丙烯酸酯作为复合活性稀释剂,1-羟基环己基苯基甲酮和双(2,4,6-三甲基苯甲酰基)苯基氧化膦作为复合光引发剂,优化低聚物用量、复配稀释剂配比及用量、复配光引发剂配比及用量等因素,获得固化速率快、黏度低并且力学性能优良的光固化环氧丙烯酸体系,并研究其性能。结果表明:当EA用含量为60%,复合稀释剂TPGDA与HDDA比值为8∶2,用量为35%,复合光引发剂184与TPO比值为4∶6,用量为4.5%时,光固化体系树脂的综合性能最优异,拉伸强度为33.42MPa,断裂伸长率为14.5%,冲击强度为2.41kJ/m^(2),其起始分解温度为322.61℃、最大分解速率温度为383.18℃、质量损失50%时的温度为392.4℃、最终的残余率为4.54%,通过拉伸断面微观形貌分析其为典型的脆性断裂。Hexanediol diacrylate and tripropylene glycol diacrylate were compounded as active diluents,1-hydroxycyclohexyl phenyl ketone and bis(2,4,6-trimethylbenzoyl)phenyl phosphine oxide were compounded as photoinitiators.Optimizing the amount of oligomers,the ratio and amount of compound diluent,the ratio and amount of compound photoinitiator to obtain a UV-curable epoxy acrylate system with fast curing rates,low viscosity and excellent mechanical properties,and its performance was studied.When the content of EA was 60%,the ratio of composite diluent TPGDA to HDDA was 8∶2,with a dosage of 35%,and the ratio of composite photoinitiator 184 to TPO was 4∶6,with a dosage of 4.5%,the comprehensive properties of the UV-curable resin system were the best,with a tensile strength of 33.42MPa,an elongation at break of 14.5%,and an impact strength of 2.41kJ/m^(2).The initial decomposition temperature was 322.61℃,the maximum decomposition temperature was 383.18℃,the temperature at 50%mass loss was 392.4℃,and the final residual rate was 4.54%.It was a typical brittle fracture according to the tensile section microscopic morphology analysis.

关 键 词：光固化 环氧丙烯酸酯 拉伸强度 冲击强度 

分 类 号：TQ322.4[化学工程—合成树脂塑料工业]