基于逆向工程和3D打印的踝足矫形器产品设计  被引量:1

Design of Ankle and Foot Orthosis Products Based on Reverse Engineering and 3D Printing

在线阅读下载全文

作  者:宁天亮 王坤 王领彪 韩鹏飞 闫超伟 李方祺 NING Tian-liang;WANG Kun;WANG Ling-biao;HAN Peng-fei;YAN Chao-wei;LI Fang-qi(School of Mechanical Engineering,Inner Mongolia University of Technology,Hohhot 010000,China;Rehabilitation Aids Center of Inner Mongolia Autonomous Region,Hohhot 010000,China)

机构地区:[1]内蒙古工业大学机械工程学院,内蒙古呼和浩特010000 [2]内蒙古自治区康复辅助器具中心,内蒙古呼和浩特010000

出  处:《塑料科技》2024年第2期106-111,共6页Plastics Science and Technology

基  金:2021年内蒙古工业大学科研启动金项目;2022年内蒙古自治区直属高校基本科研业务费项目(JY20220026);2023年内蒙古自治区直属高校基本科研业务费项目(JY20230003)。

摘  要:传统工艺如石膏制作的足踝矫形器存在气密性低、制作效率低、舒适度差等缺点。针对此问题,文章采用逆向工程结合3D打印技术对踝足矫形器进行定制式设计,获取足部STL数据,联合逆向建模软件Geomagic studio与Rodin 4D对矫形器关键部位修型,用Grasshopper进行轻量化设计,降低打印成本与质量,通过有限元分析验证其力学性能,使用聚乳酸通过FDM 3D打印技术打印实物,并进行穿戴测试。结果表明:重建后模型精度最大偏差为0.868 mm,标准偏差0.0471 mm,模型构造精准。镂空后的矫形器在30 N碰撞集中载荷下,2 mm厚度矫形器晶格中部峰值应力为16.32 MPa,最大变形1.49 mm,晶格右侧峰值应力为15.64 MPa,最大变形0.78 mm,峰值应力均小于PLA材料抗拉强度,最大变形均小于产品本身厚度2 mm,力学强度性能符合后续生产设计要求,实物穿戴测试表明产品舒适度较好。The traditional process of foot and ankle orthoses made of gypsum has the disadvantages of low air tightness,low production efficiency and poor comfort.In order to solve this problem,this paper uses reverse engineering combined with 3D printing technology to customize the design of the ankle foot orthosis,obtains the foot STL data,combines the reverse modeling software Geomagic studio and Rodin 4D to modify the key parts of the orthosis,uses Grasshopper to carry out lightweight design,reduces the printing cost and quality,verifies its mechanical properties through finite element analysis,uses polylactic acid to print the physical object by FDM 3D printing technology,and conducts wear tests.The results show that the maximum deviation of the model accuracy after reconstruction is 0.868 mm,and the standard deviation is 0.0471 mm,and the model structure is accurate.Under the concentrated load of 30 N collision,the peak stress in the middle of the 2 mm thickness orthosis is 16.32 MPa,the maximum deformation is 1.49 mm,the peak stress on the right side of the lattice is 15.64 MPa,the maximum deformation is 0.78 mm,the peak stress is less than the tensile strength of PLA material,the maximum deformation is less than the thickness of the product itself by 2 mm,the mechanical strength performance meets the requirements of subsequent production design,and the physical wear test shows that the product comfort is good.

关 键 词:3D打印 踝足矫形器 逆向工程 轻量化设计 有限元分析 

分 类 号:TQ320.66[化学工程—合成树脂塑料工业] TP391.7[自动化与计算机技术—计算机应用技术]

 

参考文献:

正在载入数据...

 

二级参考文献:

正在载入数据...

 

耦合文献:

正在载入数据...

 

引证文献:

正在载入数据...

 

二级引证文献:

正在载入数据...

 

同被引文献:

正在载入数据...

 

相关期刊文献:

正在载入数据...

相关的主题
相关的作者对象
相关的机构对象