检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:张强 张晓晨 王柄楠 毛海峰 李明星 Zhang Qiang;Zhang Xiaochen;Wang Bingnan;Mao Haifeng;Li Mingxing(State Grid Ningxia Electric Power Co.,Ltd.,Yinchuan Ningxia 750001,China;School of Civil Engineering,Xi’an University of Architecture&Technology,Xi’an Shaanxi 710055,China)
机构地区:[1]国网宁夏电力有限公司,宁夏银川750001 [2]西安建筑科技大学土木工程学院,陕西西安710055
出 处:《山西建筑》2024年第14期1-5,共5页Shanxi Architecture
基 金:国网宁夏电力公司科技项目(SGNXJS00-JYJS2200155)。
摘 要:基于“三拉一压”复合横担,提出了一种带二分拉杆的FRP复合横担,解决了横担与塔身连接构造不合理的问题,同时保证了横担有足够的刚度。对带二分拉杆的FRP复合横担进行静力试验,研究其承载性能和破坏模式。结果表明:横担的荷载与位移基本成线性变化规律;复合材表面未出现明显变形;横担梁复合材应变远大于其钢套管应变,且越靠近加载端应变越大;受拉侧拉杆复合材应变大于横担梁复合材应变,说明受拉侧拉杆受力较横担梁大,更易发生破坏;横担的失效形式为受拉侧拉杆复合材和钢套管之间的胶接滑移破坏,拉杆的承载力决定了横担的极限承载力。横担在设计荷载以及破坏荷载作用下各构件截面应变均处于弹性阶段,其纵向破坏荷载约为设计荷载的5倍,说明该横担具有良好的受力性能,有较大的安全裕度。Based on the“three pulling and one pressing”composite crossarm,a FRP composite crossarm with split tie rod is proposed.The problem of unreasonable connection structure between the crossarm and the tower body is solved,and sufficient stiffness of the crossarm is ensured.The static test of FRP composite crossarm with split tie rod is carried out to study its bearing performance and failure mode.The results show that the load and displacement of the crossarm basically change linearly;There is no obvious deformation on the surface of the composite;the strain of the composite of the crossarm beam is much greater than that of the steel sleeve,and the closer it is to the loading end,the greater the strain is;The strain of the tension side tie rod composite is greater than that of the crossarm beam composite,which indicates that the tension side tie rod is more stressed than the crossarm beam and is more prone to damage;The failure mode of the crossarm is the adhesive slip failure between the tension side tie rod composite and the steel sleeve.The bearing capacity of the tie rod determines the ultimate bearing capacity of the crossarm.Under the design load and failure load,the section strain of each member of the crossarm is in the elastic stage,and its longitudinal failure load is about 5 times of the design load,indicating that the crossarm has good mechanical performance and large safety margin.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:3.21.126.184