La含量对高钛钢缓冷凝固组织及TiN析出行为的影响  

Effect of La content on the microstructure and TiN precipitation behavior of high-titanium steel during slow cooling solidification

作　　者：万勇 汤传圣 杨光维 张雪鉴 温永红 Yong WAN;Chuansheng TANG;Guangwei YANG;Xuejian ZHANG;Yonghong WEN(Key Laboratory of Metallurgical Emission Reduction&Resources Recycling(Anhui University of Technology),Ministry of Education,Ma'anshan,Anhui 243002,China;Baosteel Central Research Institute,Baoshan Iron and Steel Co.,Ltd.,Shanghai 201999,China;School of Metallurgical Engineering,Anhui University of Technology,Ma'anshan,Anhui 243002,China)

机构地区：[1]冶金减排与资源综合利用教育部重点实验室(安徽工业大学),安徽马鞍山243002 [2]宝山钢铁股份有限公司宝钢中央研究院,上海201999 [3]安徽工业大学冶金工程学院,安徽马鞍山243002

出　　处：《过程工程学报》2024年第7期852-862,共11页The Chinese Journal of Process Engineering

摘　　要：本工作采用高温熔炼实验以及光学显微镜(OM)、扫描电镜(SEM)等方法,研究了四种La含量对高钛钢缓冷凝固组织及其钢中TiN析出行为的影响。结果表明,凝固冷速为0.17℃/s时,各实验钢凝固组织均为等轴晶。在低La含量(0.0013wt%)下,La体现出明显脱O,S,Al能力,因此其钢中主要生成LaAlO_(3),La_(2)O_(2)S;在高La含量(0.0052wt%,0.0223wt%)下,La刚开始体现出明显脱O,S,Al能力,随着O原子的大量消耗,La的脱O,S能力快速增强。因此,其钢中主要生成La_(2)O_(2)S且部分La_(2)O_(2)S会依附于先析出的LaAlO_(3),表面形核、长大。本实验钢中TiN主要析出于Liquid+δ两相区,LaAlO_(3),La_(2)O_(2)S优先于TiN析出且与TiN的错配度小是其易成为TiN异质形核核心的主要原因。当钢中La含量为0wt%,0.0013wt%,0.0052wt%,0.0223wt%时,各实验钢中等轴晶粒平均尺寸分别为354,223,154,126μm,TiN面密度为42.2,82.9,86.3,90.7个/mm^(2),TiN平均尺寸为7.8,4.6,4.5,4.4 μm。In this work,the effects of four kinds of La content on the microstructure and TiN precipitation behavior of hightitaniumnsteel are studiedby high temperature meltingg experiment,optical microscope(OM)and scanning electron microscope(SEM).It is intended to give scientific basis and experimental data for La treatment to refine the size of TiN and the microstructure in the center region of cast ingots of high-titanium steel.The resultsshow that the solidification structures of all experimental steels are equiaxed grains when the solidification cooling rate is 0.17C/s.La shows obvious ability of deoxidization,S and Al at low La content(0.0013wt%),so LaAIO_(3),and La_(2)O_(2)S are mainly formed in its steel.La just began to show obvious ability of deoxidization,S and Al at high La content(0.0052wt%,0.0223wt%).With the consumption of a large amount of O atoms,the deoxidization and sulfur ability of La increased rapidly.Therefore,La_(2)O_(2)S is the predominant precipitate that forms in the steel,and some La_(2)O_(2)S particles will nucleate and grow on the surface of LaAIO_(3),particles that have previously precipitated.TiN mainly precipitates in the Liquid+δtwo-phase region in this experimental steel.LaAIO_(3)and La_(2)O_(2)S precipitate before TiN,and their small lattice misfit with TiN are the primary cause of their propensity to act as the cores of TiN heterogeneous nucleation.When the La content in the steel is Owt%,0.0013wt%,0.0052wt%,0.0223wt%,the average axial grain size of each experimental steel is 354,223,154,126μm,respectively.The maximum size of TiN is 19.1,11.7,11.4,10.4μm,the TiN area density in each experimental steel is 42.2,82.9,86.3,90.7 No./mm^(2),the maximum size of TiN is 19.1,11.7,11.4,10.4μm,and the average size of TiN is 7.8,4.6,4.5,4.4μm.

关 键 词：高钛钢 La处理 TIN E2EM模型 等轴晶 

分 类 号：TG142.15[一般工业技术—材料科学与工程]