49-2游泳池式轻水反应堆池底点缺陷超声测量技术研究  

Experimental Study on Ultrasonic Detection of 49-2 Reactor Pool Bottom

作　　者：杨笑[1] 张宇[1] 王硕[1] 吴东栋 丁松 YANG Xiao;ZHANG Yu;WANG Shuo;WU Dongdong;DING Song(Department of Reactor Engineering Technology,China,Institute of Atomic Energy,Beijing 102413,China;China Nuclear Power Operation Technology Corporation,Ltd.,Wuhan 430223,China)

机构地区：[1]中国原子能科学研究院反应堆工程技术研究所,北京102413 [2]中核武汉核电运行技术股份有限公司,湖北武汉430223

出　　处：《原子能科学技术》2024年第8期1616-1620,共5页Atomic Energy Science and Technology

基　　金：中国原子能科学研究院院长基金(YZ232505000302)。

摘　　要：为掌握49-2游泳池式轻水反应堆(简称49-2堆)堆水池铝质池底点缺陷的现状,以进一步为堆水池的服役性能评估提供数据支撑,确保反应堆的安全稳定运行,根据池底结构、池内介质、池壁材料等信息,研发了水浸超声测量系统,对池底点缺陷的分布情况进行了全面检查,实现了点缺陷深度的精确测量。该研究实现了首次对49-2堆池底点缺陷实际状态的远程水下无损检测,检测结论显示:与历史数据相比,池底点缺陷的分布和点坑深度测量数据基本一致,最大点坑深度为1.495 mm。研究结论为49-2堆池底材料的时限老化分析提供了重要数据支撑,研发的水下超声测量技术也可应用于同类型池式堆堆容器及乏燃料贮存池的老化管理工作以及服役寿命分析论证工作中。In order to grasp the actual state and change of the point defects on the aluminum pool bottom of 49-2 swimming pool reactor(49-2 reactor for short),to further provide data support for the service performance evaluation,and to ensure the safe and stable operation,a water immersion ultrasonic measurement system was developed according to the information of the pool bottom structure,the media in the pool,and the pool wall materials.The distribution of point defects at the bottom of the pool is examined comprehensively,and the point defect depth is accurately measured.The water immersion ultrasonic measurement equipment integrates a water immersion ultrasonic transmitter,a multi-axis scanning device and a controllable underwater floating robot.It uses ultrasonic waves to scan uneven areas such as pits on the surface of the aluminum plate.Due to changes in the surface properties of the material being tested,the sound path of the echo reflected from the ultrasonic interface changes,and the depth of the pit is obtained by measuring the difference in the sound path of the echo sound beam on the intact surface and the bottom of the pit.Before the on-site measurement,a 15 MHz water immersion point focusing probe was used to scan the pit simulation test block.At the same time,a laser confocal microscope(8.0μm step diameter)was used to measure the pit simulation test block.The scan data were compared and analyzed to determine Measurement accuracy was confirmed.In the actual inspection,the remote carrier device,that is,the underwater floating robot is used to move the scanning device to the inspection area,grid lines are used for grid scanning,and signal collection and analysis are completed through a multi-channel ultrasonic instrument.Finally,the accelerated corrosion experiment simulation analysis results were used,combined with the maximum point defect depth data measured in this study for comparative analysis,and the time-limited aging analysis conclusion of the 49-2 reactor bottom material was given.This study is the

关 键 词：49-2堆 超声检测 点缺陷 

分 类 号：TL33[核科学技术—核技术及应用]