软弹流状态下“脊-膜”织构化PDMS表面增摩特性的研究  

Enhanced Friction on PDMS Surfaces Textured with“Film-Terminated Ridges”under the Elastohydrodynamic Lubrication

作　　者：肖汉 孙勇健 王涛 时礼平[1,2] 李蒙 XIAO Han;SUN Yongjian;WANG Tao;SHI Liping;LI Meng(School of Mechanical Engineering,Anhui University of Technology,Anhui Ma'anshan 243002,China;Wuhu Technological Innovation Research Institute of Anhui University of Technology,Anhui Wuhu 241002,China)

机构地区：[1]安徽工业大学机械工程学院,安徽马鞍山243002 [2]安徽工业大学芜湖技术创新研究院,安徽芜湖241002

出　　处：《摩擦学学报（中英文）》2024年第8期1084-1091,共8页Tribology

基　　金：国家自然科学基金项目(52205178);安徽省自然科学基金项目(2108085ME174,2108085QE228)资助。

摘　　要：润滑条件下,增加软质材料(如橡胶、凝胶等)表面摩擦效应是柔性电子、皮肤传感器和智能抓取等功能器件设计制造的1个重大需求.本文中采用激光加工与多次覆膜相结合工艺,在PDMS(Polydimethylsiloxane,聚二甲基硅氧烷)表面加工出不同间距的“脊-膜”织构,研究其在流体润滑状态下接触界面的摩擦学特性,并原位考察了接触界面内润滑介质的流动特征.结果表明:“脊-膜”织构在滑动界面内产生周期性弹性迟滞,引起润滑界面的能量耗散,从而显著提高了PDMS表面在软弹流状态下的滑动摩擦效应;当“脊”间距为3 mm时,织构化表面的平均摩擦力可达100.23 mN,与光滑表面相比,其摩擦效应提高了49.6倍.此外,PDMS表面摩擦效应随法向载荷的增加而增加,但在不同滑动速度下基本保持不变.Enhancing the friction of soft materials,examples,rubber,gel,under lubricated conditions is a crucial prerequisite for designing and manufacturing functional devices like flexible electronics,skin sensors,and intelligent grasp-and-release systems.When exposed to a wet and humid environment or sliding under a lubricated case,these soft functional devices readily generate a soft elastohydrodynamic lubrication(EHL)layer on their surfaces,resulting in reduced friction force and exhibiting a low adhesion strength to the substrate.As a result,how to improve the surficial friction force of soft materials under a lubricated condition is a critical concern under the design of soft functional devices.The present study focuses on the fabrication of PDMS surfaces with“film-terminated ridges”textures,achieved through a combination of laser processing and multiple casting techniques.Subsequently,an investigation is conducted to explore their tribological characteristics at the contact interface under fluid lubrication conditions.Relative experiments were performed utilizing a home-made reciprocating friction tester.The flow characteristics of lubricating at the contact interface were also investigated in situ by an integrated digital electron microscope.The obtained results demonstrated that the sliding interface experienced an unstable behavior due to the periodic change of contact stress caused by the surfaces textured with“film-terminated ridges”.The corresponding microscopic image revealed a disruption in the lubricant flow within the contact region,accompanied by an elastic hysteresis at the interface between solid and liquid lubrication.Consequently,the energy of the contact system dissipated within the lubrication interface,which significantly enhanced the sliding friction performance of PDMS surfaces in their soft elastic lubrication state.Additionally,the enhancement in frictional force of the“film-terminated ridges”textures was highly dependent on the period spacing length of ridges.When the spacing betwe

关 键 词：弹流润滑 软材料 “脊-膜”织构 应变能 摩擦力 

分 类 号：TH117.1[机械工程—机械设计及理论]