压裂弯管冲蚀磨损数值分析  

Numerical Analysis of Erosion Wear of Fractured Bend Pipe

作　　者：王晓岗 田波 齐静静 张浩[1] 赵宁 李俊雄 李美求[3] Wang Xiaogang;Tian Bo;Qi Jingjing;Zhang Hao;Zhao Ning;Li Junxiong;Li Meiqiu(Technology Inspection Center of Shengli Oilfield,SINOPEC,Dongying,Shandong 257062,China;Safety and environmental quality management department of Shengli Oilfield,SINOPEC,Dongying,Shandong 257062,China;Institute of Strength and Vibration of Mechanical Structures,Yangtze University,Jingzhou,Hubei 434023,China)

机构地区：[1]中国石化胜利油田分公司技术检测中心,山东东营257062 [2]中国石化胜利油田分公司安全环保质量管理部,山东东营257062 [3]长江大学机械结构强度与振动研究所,湖北荆州434023

出　　处：《化工设备与管道》2024年第6期103-110,共8页Process Equipment & Piping

基　　金：国家科技重大专项课题联合任务“易损件寿命预估方法研究”(2016ZX05038-001-LH002)。

摘　　要：压裂管汇是整个压裂系统的血脉,在高负载、长周期的连续作业条件下,压裂管汇易发生刺漏、爆裂和密封失效等事故。管汇元件失效会严重影响压裂作业的进度,制约油气开采的效率和经济效益,甚至会威胁到现场施工人员的人身安全。文章建立了不同安装角度下的压裂管汇活动弯头三维仿真模型,研究了不同安装角度、颗粒的质量流量和粒径下压裂管汇的冲蚀磨损规律,并对影响压裂管汇冲蚀效果的结构参数进行多因素优化分析。结果表明:活动弯头当进出液口夹角θ为120°时,压裂管汇的冲蚀磨损程度最低;颗粒质量流量和粒径越大,对压裂管汇冲蚀磨损影响越严重;经CCD响应面法回归分析,影响冲蚀磨损速率的因素权重为管汇直径>弯头角度>弯径比。Fracturing manifold is the blood of the whole fracturing system.Under the conditions of high load and long period continuous operation,fracturing manifold is prone to leakage,burst and seal failure.The failure of manifold elements will seriously affect the progress of oil production,restrict the efficiency and economic benefit of oil and gas exploitation,and even threaten the personal safety of site construction personnel.In this paper,the three-dimensional simulation model of movable elbow of fracturing manifold under different installation angles is established,the erosion wear law of fracturing manifold under different installation angles,mass flow rate and particle size is studied,and the influence of structural parameters of fracturing manifold on erosion is optimized by multiple factors.The results show that when the inlet and outlet Angleθis 120°,the erosion wear degree of fracturing manifold is the lowest.The larger the particle mass flow rate and particle size are,the more serious the erosion wear of fracturing manifold is.According to regression analysis by CCD response surface method,the weight of factors affecting erosion wear rate is manifold diameter>elbow angle>bend diameter ratio.

关 键 词：压裂管汇 安装角度 冲蚀速率 数值模拟 

分 类 号：TE934.2[石油与天然气工程—石油机械设备]