Minimizing Weight by Optimizing Different Truss Parts Using Finite Element Analysis  

作　　者：Azad Javanmiri Jari Mäkinen Azad Javanmiri;Jari Mäkinen(Faculty of Built Environment, Tampere University of Technology, Tampere, Finland)

机构地区：[1]Faculty of Built Environment, Tampere University of Technology, Tampere, Finland

出　　处：《Engineering（科研）》2024年第11期371-389,共19页工程（英文）（1947-3931）

摘　　要：This paper presents a study of minimizing weight by optimizing different truss parts using finite element analysis and comparing Warren trusses with other trusses. The aim of the optimization is to find a light design. Existing structural steel trusses were initially optimized for minimum weight and constrained with allowable stresses and deflections. Applicable Eurocode 3 design conditions are presented, which provide the constraints for the problem. Steel truss is a preferred solution in large-span roof structures due to its good attributes, such as being lightweight and durable. Existing structural steel trusses were initially optimized for minimum weight and constrained with allowable stresses and deflections. Constant spans of the trusses have been considered, and each truss has been subjected to the same types of load cases. The top chord member load has been kept constant in each truss at 2 kN/m. Two sets of load conditions are taken as the self-weight of the truss and the snow load, but the structure is calculated by the load combination. The structural steel trusses were optimized using the design optimization tool as a first-order optimization method in RFEM, and it was extended to compare the most suitable truss geometry for the minimum weight. Finally, it is concluded that the Warren truss has a higher stiffness-to-weight ratio than other trusses after optimization. The goal of this study was to analyze all trusses and ensure that the structural stress is less than the allowable stress and that the deflection is less than the allowable deflection. The span and height are constant in all cases because they have no impact on the weight increase;only the position of the rods and cross-section size affect the building’s ability to withstand loads and weight increases. In this paper, a finite element analysis (FEA)-based optimization technique is proposed for the optimization of a light design that is constrained by allowable stresses and deflections. For this purpose, there have been studies on sizing oThis paper presents a study of minimizing weight by optimizing different truss parts using finite element analysis and comparing Warren trusses with other trusses. The aim of the optimization is to find a light design. Existing structural steel trusses were initially optimized for minimum weight and constrained with allowable stresses and deflections. Applicable Eurocode 3 design conditions are presented, which provide the constraints for the problem. Steel truss is a preferred solution in large-span roof structures due to its good attributes, such as being lightweight and durable. Existing structural steel trusses were initially optimized for minimum weight and constrained with allowable stresses and deflections. Constant spans of the trusses have been considered, and each truss has been subjected to the same types of load cases. The top chord member load has been kept constant in each truss at 2 kN/m. Two sets of load conditions are taken as the self-weight of the truss and the snow load, but the structure is calculated by the load combination. The structural steel trusses were optimized using the design optimization tool as a first-order optimization method in RFEM, and it was extended to compare the most suitable truss geometry for the minimum weight. Finally, it is concluded that the Warren truss has a higher stiffness-to-weight ratio than other trusses after optimization. The goal of this study was to analyze all trusses and ensure that the structural stress is less than the allowable stress and that the deflection is less than the allowable deflection. The span and height are constant in all cases because they have no impact on the weight increase;only the position of the rods and cross-section size affect the building’s ability to withstand loads and weight increases. In this paper, a finite element analysis (FEA)-based optimization technique is proposed for the optimization of a light design that is constrained by allowable stresses and deflections. For this purpose, there have been studies on sizing o

关 键 词：Truss Structural Optimization GEOMETRY DISPLACEMENT WEIGHT 

分 类 号：TG1[金属学及工艺—金属学]