financially supported by the National Natural Science Foundation of China (No. 51571010);the National Basic Research Program of China (No. 2015CB057400)
The influence of gas high-temperature hot corrosion(HTHC) pre-exposure on low-cycle fatigue(LCF)behavior was characterized for the directionally solidified(DS) Ni-based superalloy DZ125. Fatigue tests were carried out...
financially supported by the National Basic Research Program of China (No. 2015CB057401)
Turbine blades of gas turbine engines usually suffer from severe operational conditions characterized by high temperature and stress. Severe operational conditions during service cause microstructural changes in turbi...
financially supported by the National Basic Research Program of China(No.2015CB057400);the National Natural Science Foundation of China(No.51571010)
The effects of a MCrAlY coating on low-cycle fatigue(LCF) behavior of directionally solidified(DS)nickle-based superalloy DZ125 were investigated. Before the fatigue testings, the specimens were pre-exposed in high-te...
the National Basic Research Program of China (No. 2011CB012902) for their continuing support to this research
In this study, the microstructure evolution of rapidly solidified ASP30 high-speed steel particles was predicted using a simulation method based on the cellular automaton-finite element (CAFE) model. The dendritic g...
financially supported by the National Natural Science Foundation of China(Nos.51271016 and U1204508);the National Basic Research Program of China(No.2011CB605500);the Doctoral Program of Higher Education of China(No.20120006120042);the Fundamental Research Funds for the Central Universities(No.FRF-TP-14-062A2)
Intermetallic Ti-xAl-8Nb(x = 41,43,45,47,49;at%) alloys were solidified unidirectionally upwards with a constant temperature gradient of G=3.8 K·mm^(-1)at wide range of growth rates of v=10-400 μm·s^(-1)using...
financially supported by the National Basic Research Program of China(No.2011CB605504);the National Natural Science Foundation of China(No.51571122);the Fundamental Research Funds for the Central Universities(No.30920130121012)
Directional solidification of Ti-45Al-6Nb-xW(x=0,0.4,0.8;at%) alloys was performed by Bridgeman method with the stable growth rate of 5,10,and 20 μm·s^(-1).The differential scanning calorimeter(DSC) results in...
financially supported by the National Natural Science Foundation of China(Nos.U1204508 and 51271016);the National Basic Research Program of China(No.2011CB605501)
Microstructure and microsegregation of directionally solidified Ti-45Al-8Nb alloy were investigated by scanning electron microscopy(SEM),transmission electron microscopy(TEM) and electron probe microanalyzer(EPMA...
Project(2011CB605504) supported by the National Basic Research Program of China;Project(NCET-12-0153) supported by the Program of New Century Excellent Talents in University;Project(51274076) supported by the National Natural Science of Foundation of China
The Ti-46A1-6Nb (mole fraction, %) ingots that were directionally solidified by cold crucible were cyclic heat treated at 1330 ℃ in the a phase region. The microstructures and mechanical properties of the ingots be...
financially supported by the National Basic Research Program of China(2011CB610406);the Natural Science Foundation of Hei Longjiang Province(JC201209);the National Natural Science Foundation of China(51425402)
The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current i...
Project(51275269)supported by the National Natural Science Foundation of China;Project(20121087918)supported by the Independent Research Program,China;Project(2012ZX04012011)supported by the National Science and Technology Major Project of the Ministry of Science and Technology of China;Project(2013M540936)supported by Postdoctoral Science Foundation of China
Two multi-step (two-step and three-step) slow shot speeds were used in the vacuum die casting process of AZ91D magnesium alloy. The vacuum pressure variation in the die cavity before mold filling was monitored by us...