工业CT在工件检测中X射线硬化校正  

X-Ray Hardening Correction for ICT in Testing Workpiece

作　　者：彭光含[1] 蔡新华[1] 韩忠[2] 杨学恒[2] 

机构地区：[1]湖南文理学院物电学院 [2]重庆大学数理学院,重庆400030

出　　处：《光谱学与光谱分析》2008年第6期1426-1429,共4页Spectroscopy and Spectral Analysis

基　　金：国家科委“八五”火炬计划项目;湖南省自然科学基金项目(07JJ6106);湖南“十一五”重点建设-学科光学基金项目;湖南省教育厅科研项目(06C606)资助

摘　　要：X射线工业CT中,由于X射线能谱具有多色性,X射线在透射物质时,能量较低的射线优先被吸收,X射线能量越高,衰减系数越低。也即较高能量的X射线的衰减系数比较低能量的X射线的衰减系数小。射线随透射厚度增大,变得更易穿透,也就是发生了能谱硬化现象。由于射线硬化现象使图像重建时出现伪影,因此必须修正。文中对X射线硬化现象进行了分析,探讨了在均匀物质中,X射线射束和与透射厚度的关系。并根据Beer定律和X射线与物质作用的特点,通过获取X射线射束和数据,拟合出射束和与透射厚度的关系式。然后得出在同一透射厚度时,X射线射束和校正为单色等效射束和的关系及其等效方法。最终得出X射线等效单色射线的衰减系数的拟合值。再对此衰减系数拟合值进行卷积反投影重构,即可有效消除X射线射束硬化的影响。Since energy spectrum of X-ray is polychromatic source in attenuation coefficient with energy leads to the lower energy of X-ray X-ray industrial computerized tomography, the variation of radiation being absorbed preferentially when X-ray is transmitting the materials. And the higher the energy of X-ray, the lower the attenuation coefficient of X-ray. With the increase in the X-ray transmission thickness, it becomes easier for the X-ray to transmit the matter. Thus, the phenomenon of energy spectrum hardening of X-ray takes place, resulting from the interaction between X-ray and the materials. This results in false images in the reconstruction of X-ray industrial computerized tomography. Therefore, hardening correction of energy spectrum of X-ray has to be done. In the present paper, not only is the hardening phenomenon of X-ray transmitting the materials analyzed, but also the relation between the X-ray beam sum and the transmission thickness of X-ray is discussed. And according to the Beer law and the characteristics of interaction when X-ray is transmitting material, and by getting the data of X-ray beam sum, the relation equation is fitted between the X-ray beam sum and X-ray transmission thickness. Then, the relation and the method of equivalence are carried out for X-ray beam sum being corrected. fitted value for X-ray transmitting the material is reasoned out. Finally, the equivalent and monochromatic attenuation coefficient The attenuation coefficient fitted value is used for product back- projection image reconstruction in X-ray industrial computerized tomography. Thus, the effect caused by X-ray beam hardening is wiped off effectively in X-ray industrial computerized tomography.

关 键 词：X射线 ICT 硬化校正 射束和 

分 类 号：O434.1[机械工程—光学工程] TP391[理学—光学]