龙眼树枝修剪机具刀片切割力的影响因素试验  

Experiment on influencing factors of cutting force of blades of trim tool for longan branch

作　　者：吴良军[1,2] 杨洲[1,2] 段洁利[2] 汪刘一[2] 王慰祖[2] 刘嘉龙[2] 王亮[2] 

机构地区：[1]南方农业机械与装备关键技术教育部重点实验室,广州510642 [2]华南农业大学工程学院,广州510642

出　　处：《农业工程学报》2012年第24期8-14,共7页Transactions of the Chinese Society of Agricultural Engineering

基　　金：国家科技支撑计划项目课题(2011BAD20B10-2);国家公益性行业(农业)科研专项经费项目课题(200903023-05);广东省高等学校高层次人才项目(粤财教[2011]431号);广东省现代农业产业技术体系建设专项(粤财教[2009]356号)

摘　　要：为降低机械化修剪机具刀片切割力,提高切口质量,该文在自制切割试验台上进行了石硖品种龙眼树枝切割试验。对树枝直径、切割速度、切割间隙、动刀刃角和动刀刃形5因素进行了单因素试验。在单因素试验的基础上选取正交试验的因素水平,进行了刀片峰值切割力正交试验。单因素试验结果表明,刀片峰值切割力均值与树枝直径呈极显著幂函数正相关关系,与切割速度之间呈显著对数函数负相关关系,与切割间隙之间呈显著二次多项式函数关系,与动刀刃角之间呈极显著指数函数正相关关系;外圆弧形刃口刀片切断同样直径的树枝时最省力。正交试验结果表明,切割速度为500mm/min,切割间隙为0.9mm,动刀刃角为10°时,峰值切割力最小为1.58kN。试验结果为设计省力、切割质量好的刀片提供了依据。In order to reduce cutting force of blade and improve cutting quality of mechanical pruning machinery, using ＂Shixia＂ branch as experimental material, cutting test was conducted in the accurate micro-controlled electronic universal testing machine with a self-made cutting device. An investigation was undertaken to study the effect of branch diameter, cutting speed, cutting gap, blade bevel angle and edge curve on the peak cutting force of moving blade. Average value of the peak cutting force was increased from 0.67 to 4.13 kN as the branch diameter was increased from 10.58 to 29.43 ram. When the cutting speed was increased from 20 to 500 mm/min, average value of the peak cutting force was decreased from 2.19 to 1.76 kN. Average value of the peak cutting force was decreased linearly as the cutting gap was increased from 0.05 to 0.5 mm and then slowly increased as the cutting gap was increased from 0.7 to 2 mm. As the blade bevel angle was increased from 5° to 30°, average value of the peak cutting force was increased from 1.88 to 3.26 kN. Cylindrical curve edge blade was the most force-saving with cutting off branch of the same diameter. The relevant changing trends of the peak cutting force and cutting parameters were analyzed with statistical software. The results showed that there was an significantly positive power function correlation between the peak cutting force and branch diameter, significantly negative logarithm function correlation between the peak cutting force and cutting speed, two polynomial function correlation between the peak cutting force and cutting gal5 and significantly positive exponential function correlation between the peak cutting force and blade bevel angle. Factors and levels of the orthogonal experiment were selected based on the single-factor test. Cutting speed, cutting gap and blade bevel angle were selected to perform the orthogonal experiment with the peak cutting force of moving blade as the test index. The orthogonal experiment results showed that the optimal combined pa

关 键 词：切割装置 修剪 切割 试验 影响因素 龙眼树枝 

分 类 号：S776.274[农业科学—森林工程]