油料冷态预榨过程的油脂径向渗流模型及验证  

Radial seepage model and verification for oil in oilseeds processing by cylinder press

作　　者：刘汝宽[1,2] 柯佳见 肖志红[1] 李培旺[1] 张爱华[1] 李昌珠[1] 

机构地区：[1]湖南省林业科学院生物能源研究所,长沙410004 [2]中南大学化学化工学院,长沙410083 [3]中南大学机电工程学院,长沙410083

出　　处：《农业工程学报》2016年第19期274-279,共6页Transactions of the Chinese Society of Agricultural Engineering

基　　金：国家自然科学基金项目(31470594);国家科技支撑(2015BAD15B02);长沙市科技计划(k1508130-61)

摘　　要：为量化考察油料一维压榨过程中油脂的流动状态,针对直筒式冷态压榨制油过程,通过简化假设建立了一维压榨模型,并对油料微元进行受力分析;利用Darcy渗流定律与Terzaghi固结理论建立了油料压榨过程中的渗流模型,确定了影响压榨出油效果的因素主要为料筒内径、物料层高度、压榨压力、压榨时间、油脂黏度和物料孔隙度。在实际压榨过程中,压榨压力和压榨时间易控制,油脂黏度和孔隙度也可以通过设置压榨参数而改变,而压榨机的料筒规格不易改变,因此料筒半径的选取尤为重要。基于此,根据渗流模型推导出油率模型,分析了料筒半径对出油率的影响关系,指出料筒内径不宜过大。开展不同筒径时的出油率试验,并与模型预测值对照,其最大误差为2.10%。研究结果为油料直筒式低温预榨制油设备制造及工艺参数的优化及选取提供了参考。There are 2 kinds of methods for oilseed processing, which are mechanical pressing and solvent extraction. In mechanical pressing, screw pressing is widely used in industry for large-scale oilseeds with a low residual oil in cake while hydraulic pressing is suitable for special oilseeds under a low temperature. One-dimensional pressing is the foundation of mechanical pressing especially for new type of oilseeds with high oil content and high protein content. In process of one-dimensional pressing, oilseeds are squeezed and ruptured under the interaction with the barrel by the axial compression and lateral limit. Oils in the cells are gradually squeezed out only leaving the cake inside the cylinder barrel. In order to quantitate the flow state of oil in cold processing by cylinder pressing, experiments for stress analysis of oilseed were carried out on the basis of one-dimensional pressing model, which was established through simplifying assumptions. Based on the Darcy percolation law and the Terzaghi consolidation theory, 4 assumptions were raised： material layer of oilseeds was saturated by oil; gravity of the oil was ignored and oil flowed only in radial direction in cake pores; material of solid particles could be compressed while its volume and true density would not change, and the oil inside the pores could be incompressible; oilseeds remained in the state of saturation when squeezed and the flow of oil obeyed the Darcy seepage law. The influencing factors, including inner diameter, height of material layer, pressing pressure, pressing time, viscosity of oil, and porosity of oilseeds, were determined to establish the percolation model. Cylinder radius was one of the important factors for hydraulic pressing. The oil yield efficiencies were almost invariant with the increase of cylinder radius at first, and then decreased because oils inside pores could not flow out in time. Meanwhile pressure of hydraulic pressing would decrease with the increase of cylinder radius, leading to a difficulty for oil flow. Re

关 键 词：模型 工艺 试验 渗流定律 固结理论 油料 冷榨 流速模型 

分 类 号：TQ641[化学工程—精细化工]