检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:沈雪[1] 田于逵[1] 张璇[1] 孙海浪[1] 谢华[1] 张楠[1]
机构地区:[1]中国船舶科学研究中心水动力学国防科技重点实验室,江苏无锡214082
出 处:《实验流体力学》2017年第3期66-71,共6页Journal of Experiments in Fluid Mechanics
基 金:国家重大科学仪器设备开发专项(2013YQ040911)
摘 要:针对MEMS壁面剪应力传感器进行了标定及其不确定度分析工作。标定基于压力梯度法,使用扁平校验水槽作为主要的试验装置。测量不同壁面剪应力下的MEMS输出电压信号,通过最小二乘拟合可获得标定系数。反复进行壁面剪应力及电压测量,同时查找相关产品说明书获得壁面剪应力及标定系数的不确定度。试验结果表明,剪应力测量的相对扩展不确定度小于7%,且外流速度越大,剪应力测量的不确定度越小,因此扁平校验水槽能够提供较高精度的剪应力输入;电压测量的相对扩展不确定度小于7%,且外流速度越大,电压测量的不确定度越小,因此传感器能够可靠地用于流体壁面剪应力的测量;标定曲线具有合理的形态且拟合相关性较高,因此标定公式具有较好的可靠性。In this paper, the calibration and uncertainty analysis of the MEMS shear stress sensor are undertaken. Shear stress is generated by the pressure gradient method, the main testequipment is the flat verification water channel. Different voltage outputs are measured ferent wall shear stress conditions, and the calibration coefficient can be got through matching the shear stress and voltage with the least square method. The shear stress uncertainty and caii- bration coefficient uncertainty can be got through measuring the pressure and voand checking the related product manual. As the resutt indicated,the uncertainty of the shear stress measurement is within 7 % , it tends to be smaller as the free-stream velocity gets higher. The uncertainty of the voltage measurement is within 7 % , and it also tends to be smaller as the free-stream velocity gets higher, so that the sensor can be used to wall shear stress mreliably. The shape of calibration curve is reasonable, its correlation coefficient of fitting is large enough,it means that the calibration equation is reliably.
关 键 词:MEMS传感器 壁面剪应力 标定 压力梯度法 扁平水槽
分 类 号:TV131[水利工程—水力学及河流动力学] TH823[机械工程—仪器科学与技术]
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.200