检索规则说明:AND代表“并且”;OR代表“或者”;NOT代表“不包含”;(注意必须大写,运算符两边需空一格)
检 索 范 例 :范例一: (K=图书馆学 OR K=情报学) AND A=范并思 范例二:J=计算机应用与软件 AND (U=C++ OR U=Basic) NOT M=Visual
作 者:薛海[1] 胡李军 李强[2] XUE Hai;HU Lijun;LI Qiang(School of Mechatronic Engineering,Lanzhou Jiaotong University,Lanzhou Gansu 730070,China;Engineering Research Center of Structure Reliability and Operation Measurement Technology of Rail Guided Vehicles of Ministry of Education,Beijing Jiaotong University,Beijing 100044,China)
机构地区:[1]兰州交通大学机电工程学院,甘肃兰州730070 [2]北京交通大学轨道车辆结构可靠性与运用检测技术教育部工程研究中心,北京100044
出 处:《中国铁道科学》2021年第1期105-115,共11页China Railway Science
基 金:甘肃省高等学校科研项目(2018B-028);北京交通大学轨道车辆结构可靠性与运用检测技术教育部工程研究中心开放课题(219008);兰州交通大学—天津大学联合创新基金项目(2020058)。
摘 要:针对仿真或仅考虑紧急制动状态下动车组制动盘盘毂安全性分析中存在的不足,基于盘毂应力在线测试,分析动车组高速运行和不同制动方式下盘毂的频谱特性和成分特性;考虑应力集中,根据静力等效原则进行毂齿根部的应力线性化,分析不同制动方式对盘毂疲劳损伤的影响;采用指数模型拟合和核密度估计相结合的方法,推理97.5%置信度下的盘毂实测应力谱,并考虑车轮镟修前后盘毂损伤演化和材料强度退化,评估盘毂服役安全性。结果表明:盘毂载荷振动频率主要分布在0~71 Hz和341~680 Hz频带,车轮镟修可有效降低341~518 Hz频带内的载荷振动、消除518~680 Hz频带内的载荷振动;动车组高速运行和车轮状态不良是造成盘毂损伤的主要原因;若按盘毂服役寿命为1500万km计算,盘毂疲劳薄弱区的等效应力为37.4 MPa,累积损伤为0.61,该结果可为盘毂的结构设计和检修维护策略制定提供依据。In order to make up for the shortcomings in the safety analysis of EMU brake disc hub mostly through virtual simulation or only considering emergency braking,the spectral characteristics and composition properties of EMU disc hub were analyzed under high speed operation and different braking modes based on the online test of hub stress.Considering the stress concentration,the stress at the root of hub tooth was linearized according to the principle of static equivalence,and the influence of different braking modes on the fatigue damage of disk hub was analyzed.The measured stress spectrum of the hub was inferred on the confidence level of 97.5%based on the combination of exponential model fitting and kernel density estimation.The service safety of the hub was evaluated considering the damage evolution of the hub and the strength degradation of the material before and after wheel reprofiling.Results show that the load vibration frequency of the hub is mainly distributed in the frequency band of 0~71 Hz and 341~680 Hz.Wheel reprofiling can effectively reduce the load vibration in the frequency band of 341~518 Hz and eliminate the load vibration in the frequency band of 518~680 Hz.The main causes of disc hub damage are the high speed operation and poor wheel condition of EMU.If the service life of disk hub is 15 million kilometers,the equivalent stress in the fatigue weak area of the hub is 37.4 MPa,and the cumulative damage is 0.61.The results can provide the basis for the structural design and maintenance strategy of the disk hub.
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在载入数据...
正在链接到云南高校图书馆文献保障联盟下载...
云南高校图书馆联盟文献共享服务平台 版权所有©
您的IP:216.73.216.171